Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Few questions on a 350 sbc build up...
User Name
Password
lost password?   |   register now

Thread: Few questions on a 350 sbc build up... Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-16-2012 11:08 PM
vinniekq2 some 350s can be bored 060,so 4.06 bore x 3.875 stroke = small bore 401. American racing engines offers this combo.
07-16-2012 10:44 PM
Uniryan2008 Sounds like a nice setup, Im jus tryin to get away from the stereotypical sbc, make it a little interesting next time around, somethin not many see or even hear of, know of any other somewhat simple to build unusual sbc's?
07-16-2012 10:18 PM
vinniekq2
1.2

thats a good amount of HP per cube.I would like a 4.155 bore x 3.62 stroke for 392 cubes,big bore 350,heads would breathe better and rev like a 350.no need for reduced diametre cam
07-16-2012 10:07 PM
Uniryan2008 I havent built it yet, but that would be nice if that's what I get to start with, where did the 1.2 come from?
07-16-2012 09:59 PM
vinniekq2 352 cubes times 1.2 HP/= 420 horse power?
07-16-2012 09:42 PM
Uniryan2008 Sbc 400 block stock pistons 6 inch rods and 327 crank, they are screaming beasts that like it high.
07-15-2012 02:56 PM
454C10 what is a destroked 352?
07-15-2012 09:28 AM
Uniryan2008 Ok! Thank u both so much for yalls input, it's my first sbc build, jus didn't want a bone stock in my truck, my next build will be a destroked 352.
07-15-2012 09:12 AM
vinniekq2
estimate

My estimate might be fairly accurate for your application.The engine I took out of my 1981 vette was 030 over 350 with a holley street dominator manifold,modified 650 holley DP with 850 baseplate,420 lift 198/208 @ 050 cam,small tube headers.The engine was built by professional builder Jack Muzzomo. Chasis dyno tuned on a dyno jet it put down 205 HP at 4500 rpm and torque peaked just under 280.
with 2.73 gears the car was not spectacular. I now use 3.50 gears and a stroker engine.
07-15-2012 08:24 AM
Uniryan2008 Yes that is the cam I have, and that street dominator is the dual plane z28 style, I knew gears were a givin if I want it to have any jump at a stand still, so that will be a part of this build, it has the stock rear end which I can't find any gearsets for, i was thinking an early 90's reared should be a lot better seems how I can hop it up a bit easier, any suggestions???. What about a throttle spacer should I put it on or leave it off??, one of my wrenchin buddies says some offer brutal low end add, and I was told also they where for tuning not all that?? All I know is you can slap together a bunch of ****** ****,but if ain't tuned right it ain't gonna be worth a ****, I've built a lot of power jus gettin it all dialed in and tuned perfect
07-15-2012 04:05 AM
spinn 350 is great for a performance engine build. The power is made from the package. Use parts that are made to work together and are proven.

Melling is the performer cam 420/442 lift , correct. I would use the performer intake. Not the RPm intake unless you have a lot of gear 4.10+ . Stay away from most single plane manifolds on the street.

NA hydraulic cammed, 9 ish to 1 engines I have built are good for .75-.85 power per inch. A sbc making 300hp is a fast engine with a good amount of power.

Lift should clear the pistons. Do not really worry about that till over .450 lift.

Not sure about rejeting , but a 600 holley at baseline should be pretty close. Better than a 770 in a heavy longbed.
07-15-2012 12:45 AM
Uniryan2008
Few questions on a 350 sbc build up...

I have a '73 sbc 350 w/flat tops not sure if it's been bored, I've bought a melling mtc-1 to go in it and I'm going to slap a 300-36 Holley Street Dominator intake that has been polished but not ported on top of it, I only have a 600cfm vs Holley right now with stock E.manifolds. First of all is that cam going to be to much lift for my pistons?? Second will I need to rejet that carb for more fuel?? And third,what kind of numbers should I be pushin after if it all plays out fine???
I will later be putting long tube full lengths on her with a 770cfm street avenger, it's in an '81 gmc long bed. Thank you for any replies.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.