Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 350 sbc fouled spark plugs
User Name
Password
lost password?   |   register now

Thread: 350 sbc fouled spark plugs Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-16-2012 04:40 PM
cobalt327
Quote:
Originally Posted by grandslam1991 View Post
Ill definitely pull the valve cover to check the cam first, hate to do work that doesnt need to be done, thanks bogie.
Have you retightened the intake bolts? It often takes three or four times retightening before they take a set and hold torque.

Not saying to over tighten them, just start from the inside and work towards the ends, swapping sides as you go. If the gaskets haven't degraded totally, they still might seal. Might.

If you end up replacing the intake gaskets, be sure to retighten after a couple heat cycles. Repeat until the bolts are staying tight.
07-16-2012 02:55 PM
grandslam1991 Ill definitely pull the valve cover to check the cam first, hate to do work that doesnt need to be done, thanks bogie.
07-16-2012 02:36 PM
oldbogie
Quote:
Originally Posted by grandslam1991 View Post
Yes the intake installed about 2000 miles ago, and i believe i bought fel pro gaskets and had my mechanic the intake. Maybe ill replaced those gaskets and see if it helps.
While I do suspect the intake gaskets, I start with pulling the rocker cover and check the valve motion first as this is easier than getting the intake off and allows ruling the cam lobes in or out as a problem with a minimum of effort before pulling the intake.

Bogie
07-16-2012 12:29 PM
grandslam1991 Yes the intake installed about 2000 miles ago, and i believe i bought fel pro gaskets and had my mechanic the intake. Maybe ill replaced those gaskets and see if it helps.
07-16-2012 11:19 AM
oldbogie
Quote:
Originally Posted by grandslam1991 View Post
Hi my 350 sbc seems to keep fouling the 2 front spark plugs on the driver's side of the engine. I replaced all plugs about 600 miles ago, and the other day on the highway it starts to pop and backfire out exhuast. Got home and removed al plugs to check, the 2 mentioned were covered in a black tar looking substance, which i managed to clean off with a wire pad, for the time being. The other plugs all ok. The engine has a brand new edelbrock 600 performer carb and edelbrock rpm air gap intake. Other then that engine is bone stock. Being that its only these 2 plugs fouled i dont think its a fuel problem, maybe oil getting into these 2 cylinders? I've heard that it could be worn valve guide or seal, intake gasket, or piston rings (doubtful about rings though as it is only 2 cyl that are bad). Is there anyway i can go about checking before i go ahead and replaced intake gaskets?? Should i pull valve covers first??
If this is a a 1970's early 1980's model you can add wiped cam lobes to you list.

Bogie
07-16-2012 11:10 AM
DoubleVision I had this same problem at one time. What your finding on the plugs is oil.
You said you added the intake and carb, was it recent? If so I suspect the intake gaskets did not seal. Sometimes you can pull the carb and if you find oil in the plenum then it's got a leak. Also in many cases guys will buy a new intake and they always seem to want to use fel pro gaskets. Certain fel pro gaskets are not for use with aluminum intakes and will not seal up. I always use the cheap paper hanging off the shelf Mr. Gasket jobs.
07-16-2012 11:07 AM
grandslam1991
350 sbc fouled spark plugs

Hi my 350 sbc seems to keep fouling the 2 front spark plugs on the driver's side of the engine. I replaced all plugs about 600 miles ago, and the other day on the highway it starts to pop and backfire out exhuast. Got home and removed al plugs to check, the 2 mentioned were covered in a black tar looking substance, which i managed to clean off with a wire pad, for the time being. The other plugs all ok. The engine has a brand new edelbrock 600 performer carb and edelbrock rpm air gap intake. Other then that engine is bone stock. Being that its only these 2 plugs fouled i dont think its a fuel problem, maybe oil getting into these 2 cylinders? I've heard that it could be worn valve guide or seal, intake gasket, or piston rings (doubtful about rings though as it is only 2 cyl that are bad). Is there anyway i can go about checking before i go ahead and replaced intake gaskets?? Should i pull valve covers first??

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:26 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.