Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Alternator question
User Name
lost password?   |   register now

Thread: Alternator question Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-21-2012 10:39 AM
regulator control

I'm not an electrical engineer - sounds like both of the "one wire" regulators are behaving the same - correct? The main lead is also the "sensor" for the regulator - and it controls the output to a fixed offset to the voltage where you are connected into the system. Your system must have very low draw at idle - and sag as the engine runs up - and the regulator is "mirroring" the sag.

The single "one wire" lead is supposed to be a large as possible to make sure the "sense" voltage is as high as possible - any drop due to resistance in the wire subtacts from the output. On mine - I ended up with a #6 fine stranded welding cable (crimped and soldered end lugs) that runs back to where the battery joins the starter solenoid. You can dummy this set-up with a single jumper cable as a test if you think the wire size is an issue - or at least rule it out.
07-19-2012 11:37 AM
Alternator question

Thanks for your reply. I am aware of the rpm requirement. This alternator comes in at 800 rpm, so it shows almost 13.9 v right away. My concern is that when you increase the rpm the voltage drops down to no lower than 12 volts. As soon as it returns to idle, the volts go back to 13.9 or so. What is puzzling, is that I put my old alternator back on and it does the same thing (1-wire also).
07-19-2012 11:11 AM
toddalin I hope that you recognize that with a "1-wire," you first have to raise the RPM up past ~1,500 to get the field to energize. After that it should work like a regular old alternator/regulator combination until you shut off the engine.

My 1-wire puts out little at idle, but ~13.9 volts when the RPM climbs as measured at the battery.
07-19-2012 09:10 AM
Alternator question

My '40 Ford has a 350 Chevy. I'm using a new Tuff-Stuff 100 amp 1-wire alternator. At idle, the voltmeter reads 13.9 volts. When the rpm is raised, the voltage starts dropping to around 12 volts. I had the alternator tested and was told it was putting out fine. The guy told me that 1-wire alternators don't always read voltage the way regular alternators do. Anyone have thoughts on this?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 02:11 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.