Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Awesome budget 400 sbc block builds
User Name
Password
lost password?   |   register now

Thread: Awesome budget 400 sbc block builds Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-18-2012 05:08 AM
6426yy http://www.google.com/url?sa=t&rct=j...oiJlqZq9H3h6XQ

I'm doing one of these builds pretty soon, gathering parts now.
08-18-2012 02:36 AM
stallion0606 I ment to say 35 inch tires. I was reading earlier about the small block 400, which i do have a compllete one. has been rebuilt once, but the kid who had it spun #3 rod bearing. plans are to rebuild it again at put it in a 79 chevy silverado 1/2 ton 4x4. any suggestions on more horsepower and torque for this engine.
08-04-2012 04:29 AM
stallion0606 what could i expect from a 400sbc bored +.030 with flat top pistons. stock heads and stock rods stock crank maybe a mild cam for a 79 chevy 4x4. running 3.73 gears with 25 inch tires. i have 4.11 gears for rear and 4.10 for front but an a tight budget and never put gears in diffs. so im not real confident on installing them. any thought would be appreciated.
08-03-2012 09:23 AM
vinniekq2 377 = smaller engine ,so less torque at a higher RPM.Its all simple math,,,start with what you want,add in what you have and see what it will take to get you to where you want to go.EG: If I have 400 rwhp in a 1970 Nova,set up with 4.11 gears,matching transmission to engine,the car hooks well( assuming drag race) has traction bars that are tune able, the car weighs 3500 pounds or less with driver and fuel,ready to go,he has slicks,this car will go 12.0s.

to figure out what your car will do,add or subtract 1/10 for every 10 hp up or down.If you use a (Winderupper} you will need gearing to accommodate the different powerband.for every 100 pounds difference add or subtract 1/10th.If your car is not as good at hooking as the nova,expect slower times.If you do not use slicks,expect 13s.If you dont need slicks expect slower,much slower.Add 3/10ths for exhaust system on small blocks.This is not an accurate guide but it will give you an idea where you might be or where you might get to with some tuning.
08-02-2012 08:07 PM
DOUGIEB59 Ok, here we go... What if a fella wanted to build a 377... Winderupper!!??
08-02-2012 12:15 AM
vinniekq2 power glide with 273 gears will make decent power and should make your mileage easy.not sure how hard it will launch
08-01-2012 10:37 PM
blackpanther68
Quote:
Originally Posted by vinniekq2 View Post
cheap 400 I built for a friend. 1978 monte carlo, 20 plus miles to the gallon when right foot is restrained and 14.1 1/4 mile times with 2.73 gears and white wall radials.turbo 350 with shift kit,stock converter.
Bone stock short block rebuilt with cast pistons and static balanced,stock heads.Mild 430 lift flat tappet hydraylic cam,street master manifold, 625 carter carb,1 5/8 primary headers,2 1/2 " dual exhaust not mandrel bent. no where near 400 HP,but a tonne of torque. tire melter

This sounds awesome. I am building a stock 400 with a 488/510 cam and 2.73 gears and a powerglide. 750 quadrajet aluminum intake stock heads stock bottom. I hope mines sees somewhere in the 15mpg range if my right foor is "restrained".
07-20-2012 10:55 AM
my87Z i wouldn't use the stock rods either, i was just going off of a bare bones buget build.

if he has the money i would certainly go with a larger rod, and a hyd roller cam
07-20-2012 08:07 AM
Mr. P-Body One of our friends has a '78 GMC "short bed" weighing in at 4,100 and change (with him in it), running 12.20s all week on 93. His goal was a mid 12 second pickup. He has Chevy aluminum heads (late '80s Corvette) mildly ported, Comp solid flat tappet (XS274S), 6" rods and SRP pistons. Performer RPM and Hooker... He's VERY happy, and the thing is a beast. It runs well in traffic and gets ABOUT 13-14 MPG on the "open road". 406 CID.

A nice pair of iron heads would actually make more power. This combo seems to have plenty of low-end for driving, and is severely "traction impaired".

I disagree on using stock 400 connecting rods. 5.7 rods are too cheap to ignore, and MUCH better. 6" rods are better, yet. Many pistons available either way. I DO agree, no need for a forged crankshaft as long as you have a genuine Chevrolet nodular casting. We've seen many iissues with the cheap import "cast" cranks (regardless of brand). This is the single small block application we recommend a "high volume" oil pump, due to the size of the main journals (we don't use the HV pump in "race" engines, just street).

FWIW

Jim
07-20-2012 02:16 AM
327NUT Vinnekg2......PM received and PM sent back, I understand completely and no problems whatsoever........Dave
07-20-2012 12:34 AM
my87Z if all you are looking for is a 400hp sbc 400 then dont bother with forged internals. if you can find a complete 400 (good luck!), tear it down get what ever machine work needs to be done to the rods, crank, and block done. buy a set of 18cc dished pistons, a mildly price set of 200cc runner/ 72cc combustion chamber steel heads (should put you around 9.4:1). get a hyd f/t cam with somewhere around 220-232 duration at .050, dual plane intake, 50-60k volt cheap HEI distributor, 750 vacuum sec carb, $250.00 set of headman headers, 2.5" exhaust and some decent mufflers. it will want atleast a 3.73 gear in a truck if not a 4.10 and it will probably want around a 2800-3000 stall.

bam! simple 400-430hp (easily) 440-460tq (again easily) motor that will be rather easy on the pocket.
07-19-2012 10:28 PM
Uniryan2008 I would jus like a few pointers on 400 builds,I'm not goin to diss anybody's knowledge a lot of people have done a lot of things and I enjoy discussing those times had ,that's how I learn all my knowledge since I started building sbc's and so fare been successful, thanks everybody
07-19-2012 10:19 PM
vinniekq2 mr nut,there are a few threads that are going no where.I should not have posted that but was frustrated because I was truly trying to help with the previous posts I made.
07-19-2012 10:12 PM
cobalt327
Quote:
Originally Posted by 327nut View Post
why in the world would you take a 400 and put a 3" stroke crank in it if you want a lot of torque????? Abosolutely makes no sense and vinniekg2 ???? The guy said he's on some kind of budget and you're filling his head full of bill mitchell block $$$$$. Do some reading uni and stop dreaming.
07-19-2012 10:05 PM
327NUT Why in the world would you take a 400 and put a 3" stroke crank in it if you want a lot of torque????? Abosolutely makes no sense and Vinniekg2 ???? the guy said he's on some kind of budget and you're filling his head full of Bill Mitchell block $$$$$. Do some reading Uni and stop dreaming.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.