Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Remove lower ball joints 1967 El Camino
User Name
Password
lost password?   |   register now

Thread: Remove lower ball joints 1967 El Camino Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-22-2012 03:05 PM
Chucky5150 Good news everyone!

Got the lower ball joints out. Much easier than I feared. However, it seems to be the upper ones giving me trouble now. Think I'm going to see if I can borrow one tomorrow.
07-22-2012 12:32 PM
LATECH I use a piece of 1/2 inch allthread and some washers to compress the springs, just enough to get the lower control arm bushings pinned on with the bolts.
Put allthread , (about an 18 inch piece) through the hole where the shoch absorber goes through. and at the top where it goes through the spring perch (bucket for spring)
I put 2 nuts on top end and tighten them together , then put a couple hefty washers on the bottom. Then you crank the bottom nuts down to compress the spring. Usually only a few inches is enough to get the bushing ends of the control arms close enough to slide the bolts in.
Once you have pinned the comtrol arm at the bushing end, lift the car by the ball joint end of the control arm, using the cars weight to compress the spring further so you can hang the spindle.
Once you have the spindle back on THEN remove the allthread. In case you slip before you get her coupled together, the allthread keeps the spring from flying out if things get hairy.
ALSO .. very important.. many guys make this mistake....
Dont tighten the control arm bushing bolts untill last. You need to have the car setting on its weight on the ground so the bushing is registered in the position it will be in with the car on the ground.If you dont, the center will rip out of the bushing and it will groan and creak like an arthritic old man and you wont like that, I assure you.
07-22-2012 11:44 AM
Chucky5150
Quote:
Originally Posted by Bryan59EC View Post
Either way (jack, wood, BFH or the correct tool) these thing have been in the car for nearing 50 years and will be difficult to remove.

When reinstalling----the must start in the holes absolutely square.
Not too difficult to crack the control arm upon reinstalling (done that).

I'd suggest removing the control arm and taking it to a machine shop to do the dirty work, but removing and reinstalling the springs in these cars can be a pain in the hiney.
yeah, I just removed the springs the other day. Doesn't look like it'll be fun to get back in to place.

I'll check the local part stores for a press. The top one doesn't seem to be too hard to get out.
07-22-2012 10:08 AM
Bryan59EC Either way (jack, wood, BFH or the correct tool) these thing have been in the car for nearing 50 years and will be difficult to remove.

When reinstalling----the must start in the holes absolutely square.
Not too difficult to crack the control arm upon reinstalling (done that).

I'd suggest removing the control arm and taking it to a machine shop to do the dirty work, but removing and reinstalling the springs in these cars can be a pain in the hiney.
07-21-2012 12:34 PM
LATECH Easy.. Support the car under the lower arm with a stand. Remove spindle assembly from car. Pound the joint out.
To put it in, stuff the joint back under the arm in its hole. Lift it slightly with a floor jack on the joint,use a wood block to keep from deforming the joint. Lift the cars weight onto it, then pound the control arm down to push the joint through it.
OR go to adavanced and rent the correct tool. A ball joint press is really the right way.
Lots of guys wont rent the tool or dont have local axcess to tools like that, which would be the only reason I described how to do it with the floor jack and a hammer. If you are not careful you can mess things up pretty bad.
I put many in with a floor jack and a hammer, but that is just me.
07-21-2012 12:16 PM
Chucky5150
Remove lower ball joints 1967 El Camino

Hey guys,

Car: 1967 El Camino w/ 396cid


question:

How hard is it to remove lower ball joints with control arms still attached to car?



Full story:
I am converting from drum to disk brakes and was looking into replacing all the rubber that is 45 years old while I'm at it. I've seen them being beat out by taking the control arm off and beating the ball joints out with a hammer. I don't have a vise that I can do that with and I'm not all that comfortable with taking the control arms off. Well, I'm sure I can get the control arms off, it's the getting everything back together and lined up that I don't know much about. I'm trying not to buy more tools to get this done.

I am just a little worried about getting into a bigger mess than I know what to do with and end up spending a lot more than I want.



Thank you.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:41 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.