Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> rear end choice for a 66 skylark
User Name
Password
lost password?   |   register now

Thread: rear end choice for a 66 skylark Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-25-2012 01:09 PM
big gear head The '64 to '72 A body rear ends are the only ones that wil bolt in. The '73 and later rear ends will require modifications to make them work. You can put a posi and 3.73 gears in the rear end that you have. The parts are available, but you need to find someone who knows how to set up a ring & pinion set to do the installation. Your car has the 8.2 BOP 10 bolt rear end with a 27 spline pinion and 28 spline bolt in axles. This rear end is stronger than the Chevy 8.2 10 bolt, so don't swap it for the Chevy rear end. A 12 bolt would be stronger, but a good 3.73 posi 12 bolt for a '65 or '66 A body will run you about $1000 to $1700. The '71 and '72 A body 8.5 10 bolt is a good rear end, but a little hard to find. They were used in the Cutlass and Skylark in '71 and '72 only. These may be 1 inch wider than the rear end that is in your car now. They also have bolt in 28 spline axles, but they have a 30 spline pinion.

If you have been doing one wheel burnouts and you put a posi rear end in your car you need to replace the rear tires. If one tire is worn more than the other this will cause the clutches in the posi to slip and get hot while you are driving. It could ruin the posi or possibly ruin the whole rear end because it will cook the oil. The air pressure in the rear tires also must be kept equal.
07-25-2012 12:13 PM
SSedan64 An 8.5" 10-Bolt from an 70-72 A-Body or 73*-77* A/G-Body will work = *Wider width, 1" or so.
8.5" 10-Bolt from 84-87 G-Body, Buick GN, Olds 442/HO = 58" WMS to WMS.
12-Bolt from an A-Body 65-72 Chevelle. 65-67 = 60" WMS to WMS, 68-72 = 61" WMS to WMS.

8.5" rear axle
OLDSmobility.com - The 1967 Oldsmobile Cutlass and 442 Resource - GM 10-bolt Differential Technical Information

9" Ford housing are also sold to bolt in, Quick Performance, Strange, Moser, Currie etc..

WMS = WheelMountingSurface.
07-25-2012 11:25 AM
Bad66
rear end choice for a 66 skylark

My 66 skylark has a bone stock 1 wheeler peeler rearend. I would like a 3.73 or higher posi, but I think I need a bigger housing to hold the carrier. I'd like to do this cheap, so when surfing thru Craigslist, what kind of rearend should I be looking for. I'm looking for an easy swap. Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:03 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.