Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 4L60E shift problems
User Name
Password
lost password?   |   register now

Thread: 4L60E shift problems Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-26-2012 09:18 AM
c65shoebox
Line Pressure/ Burnt clutches?

Sounds like a leak to me in the 3/4 area, pistons might be ok - their is an o ring in the input drum that needs replaced and oftern gets overlooked in which can cause a major leak, the input drums are also know for being cracked. Clutches might be smoked. Install a line pressure gauge and check pressure. Does it work cold and go away hot? Fluid level? Etc?

Sounds like an internal leak or burnt 3/4 clutch pack.
07-23-2012 07:22 PM
S10BlazerBuilt
Quote:
Originally Posted by RennMan View Post
Thanks again. That's pretty easy to look at. At least I know what I'll be doing my next day off.
You say you rebuilt it yourself, so you should know how much of a mess those check balls can be. It's much different when the tranny is installed when you pull the valve body off, rather then when the tranny is upside down on a bench. Just remember to be easy when you take the valve body off, and if you decide to pull the separator plate, which is recommended since you'll be breaking the gasket bond when you take it off, be sure to let the separator plate down as gently as possible to keep those check balls in their proper locations. I would inspect the plate to see if there are any burrs where the balls seat, and also check to see if the valves are moving as they should. Good luck with it.
07-23-2012 07:16 PM
RennMan Thanks again. That's pretty easy to look at. At least I know what I'll be doing my next day off.
07-23-2012 06:16 PM
S10BlazerBuilt
Quote:
Originally Posted by RennMan View Post
Thanks for the reply. I haven't started working on it yet. Trying to figure out what the most likely issues are before tearing into it. Doesn't seem like there would be a problem related to debris unless something is going wrong internally. I drove it some this weekend and found that when I take it really easy, it wont engage 3rd at all. But when I accelerate more agressively it will shift. Although it doesn't feel right. Llike it doesn't want to stay engaged. Thinking I might take it to a shop and have an experienced trans guy take it for a drive.
Well, I'm no expert, however, when you put it that way, it brings me back to my first statement about the valve body. Transmission fluid pressure increases when you're driving more aggressive. At least, thinking of physics here. So it makes sense. Something is sticking in the valve body. Whether it be a valve or faulty check ball...
07-23-2012 05:22 PM
RennMan Thanks for the reply. I haven't started working on it yet. Trying to figure out what the most likely issues are before tearing into it. Doesn't seem like there would be a problem related to debris unless something is going wrong internally. I drove it some this weekend and found that when I take it really easy, it wont engage 3rd at all. But when I accelerate more agressively it will shift. Although it doesn't feel right. Llike it doesn't want to stay engaged. Thinking I might take it to a shop and have an experienced trans guy take it for a drive.
07-19-2012 03:29 PM
S10BlazerBuilt
Quote:
Originally Posted by RennMan View Post
I rebuilt the 4L60E tranny in my 96 suburban about 1 1/2 years ago. Followed the ATSG Manual using a quality rebuild kit. Made a few performance mods. Shift kit, New Converter, etc. "Seemed" to run fine for a year or so, although I never pushed it very hard. Currently it shifts 1st, 2nd, and reverse but sometimes ( more often than not ) when it shifts to 3rd there is nothing there. as if it goes into neutral. The truck has 4.88 gears and 37" tires. The speedometer works but is not calibrated for the gear/tire mods. Also the gear selection indicator lights don't always work or don't work correctly. Does this look like a minor electrical/servo/calibration problem or is it more likely a major internal issue?
Have you pulled the valve body to ensure all the valves are moving without obstruction? Sometimes, even the smallest bit of debris can keep the tranny from shifting.
07-19-2012 03:08 PM
RennMan
4L60E shift problems

I rebuilt the 4L60E tranny in my 96 suburban about 1 1/2 years ago. Followed the ATSG Manual using a quality rebuild kit. Made a few performance mods. Shift kit, New Converter, etc. "Seemed" to run fine for a year or so, although I never pushed it very hard. Currently it shifts 1st, 2nd, and reverse but sometimes ( more often than not ) when it shifts to 3rd there is nothing there. as if it goes into neutral. The truck has 4.88 gears and 37" tires. The speedometer works but is not calibrated for the gear/tire mods. Also the gear selection indicator lights don't always work or don't work correctly. Does this look like a minor electrical/servo/calibration problem or is it more likely a major internal issue?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:07 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.