Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> top dead center tool?
User Name
Password
lost password?   |   register now

Thread: top dead center tool? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-18-2012 01:18 AM
graydog
Quote:
Originally Posted by poncho62 View Post
That is basically a piston stop......A simple one can be made with an old spark plug .........
I recently made one for my Gravely 1 cyl engine. It cost nothing but a little time and the rod is adjustable.
07-30-2012 10:10 PM
bentwings I have a cover on my motor. I drilled and tapped the snout hub (no balancer on blower motors) for a couple of 4-40 flat head screws from the hobby shop. The screws are located so the cover only goes on one way. I can remove it and replace it without losing location.
07-30-2012 09:14 AM
cobalt327 Sometimes guys get in trouble because the damper doesn't match the timing tab. Here is a short page describing the differences in the three types most commonly seen and how to go about remarking the damper if need be. Cost is zero, but it won't trick anyone into believing you have a Fluidampr...

It's worth mentioning that using a cover still doesn't guarantee the timing marks are accurate- even if the parts all match. Manufacturing difference and tolerance creep can still make the marks off, so the best bet is to go ahead and do the drill to determine true TDC. DV gave a link earlier for determining TDC, here it is again.

The bolt holes in the cover can be carefully elongated in order to index it correctly if you find it's off.
07-29-2012 11:03 PM
rickman2k I'm gonna get one of the cover's, it'll
be a gift from me to my motor !
there's 3 diff ones, I just gotta make sure I got the one marked for my motor plus they look really great like a Fluiddampner balancer
07-29-2012 07:31 PM
rickman2k
the purdy TDC cover

I'm gonna get one of the cover's, it's be a gift from me to my motor !
there's 3 diff ones, I just gotta make sure I got the one marked for my motor plus they look really great like a Fluiddampner balancer
06-18-2012 07:50 PM
Irelands child If you have a spark plug, it's even easier then drilling and tapping. Break out the plug insulator, find a dowel that's close in size - even a wood pencil will work. Run the piston up close to what you think is TDC (insurance so if you have an awww s@#t and lose your grip on it)put the dowell/pencil in and turn the engine via the crank bolt or whatever you use. A piece of masking tape marked/"gradulated" with a few lines will give you an idea of when TDC is reached.

Yes, that method does work and my big expenditure was a new $2 Wally World Autolite plug since I had tossed all my used ones. It sure ain't rocket science
06-17-2012 04:36 PM
bentwings I guess some us just have harder heads than others. Some have more money than common sense and some of us just like the do things the hard way. haha
06-16-2012 08:07 AM
75gmck25 I've seen several posts over the years that suggested making a piston stop from a spark plug and bolt, so I tried it one time. I finally gave up after realizing it was much more of a PIA to make the tool than it was to add it to my next Summit order and just buy it.

The piston stops cost $8-12 from Summit. If I made it myself I was going to spend at least an hour drilling and tapping the hole and I did not have a drill press or the tap and die set to do the job. I finally decided that for a savings of only $8 my time could be used better on other project work. YMMV

Bruce
04-09-2012 04:39 PM
poncho62
Quote:
Originally Posted by Old Fool
why pay for an old spark plug and a bolt?
Agreed......
04-09-2012 04:36 PM
Old Fool why pay for an old spark plug and a bolt?
04-02-2012 08:54 PM
bentwings That's the tool.

I use a proform cover but I remounted the stock pointer so it indicates true TDC......using the tool shown.

Don't forget that when you remover the damper cover it may change the "real" tdc so you need to recheck it.
04-02-2012 12:43 PM
Brian Morency
04-02-2012 11:37 AM
Brian Morency Sears doesn't sell it either. Had to go to winners circle. Was $9.99, sears could order one but it was $34.99. Auto zone website says they have them for $19.99 but don't carry it.
04-02-2012 09:45 AM
Brian Morency Just tried autozone & advanced. Neither sold tool. Waiting at sears now to open.
04-02-2012 08:59 AM
Florence95 Or if there's an easy way to find a way to mark the balancer so I can set the timing. Its not off by much but I'd like it to be set right.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:02 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.