Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Downdraft booth pit info?
User Name
Password
lost password?   |   register now

Thread: Downdraft booth pit info? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-05-2012 03:54 PM
302 Z28 Here is a shot of the floor draft with the cab of my 34 on it's side prior to painting.

Vince
08-05-2012 03:53 PM
302 Z28 The booth I used to paint my 34 was a downdraft booth, it worked fantastic. The fresh air was drawn down from the top of the booth through filters.

Sorry cannot offer much info as to size.

Vince
08-03-2012 07:46 PM
Old Fool The only details I find are an open pit with the exhaust fan pulling from the center to one side , no baffles or other obvious ways to balance the air flow.

Primitive must work ok, I stopped at the Nova Verta distributor and he said theirs have no balancing mechanism in either the inlet or exhaust .

Having worked in the trades I assumed that a booth would have a balanced air flow similar to doing T&B on the ventilation systems in commercial buildings.

*** u ME d, my first mistake.

I think I will make my pit tunable with a minimum of 3 zones, front, center, and rear.
The cost to pour the pit is only a few hundred dollars more than just a floor, so why not!
The grating will cost a bit, but some 2x6's will cover it until grating is procured.

Water in the pit is not a concern, there should never be any. If so then a small sump pump to move it outside will work fine. ( just have to remember to grade the floor of the pit to a sump, thanks for the tip)

Would like to use squirrel cage fans instead of propeller fans, quiter and cheaper per cfm to run according to the "fan experts".

Until all the parts are acquired, it will just be a 15x28 storage shed, lol.
08-03-2012 02:11 PM
skip99 when I built my shop I thought about it..but decided against it because if I got water in the pit, I had no way to get it out , other than a pump, I didnt have enough elevation to just drain....
I suppose I could have built a lip around the pit, but was just to big a PITA, so I just put fan low and to the front on wall, and air coming in the back up high, works almost as well...
08-02-2012 04:42 PM
Old Fool
Downdraft booth pit info?

I would like to know more about the pit of a downdraft booth. Anyone have details of sizing, are there baffles, vanes, or ??

Thanks,

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.