Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> What oil needed zddp
User Name
Password
lost password?   |   register now

Thread: What oil needed zddp Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-10-2012 02:14 AM
67Mustang Al. I am using 10/30 Fuchs+ crane cams zinc with .0016 clearance on rods and .0015 on the mains on a new 347. I used straight 30 mineral to run it in first. I had a melling HV pump but have now changed it out for a standard after some tech talk from Melling techs. I also installed an ARP "round" oil pump drive shaft over the straight "hex" unit.
Al
08-09-2012 11:57 PM
Hookedup12 I've broke it down to either brad penn or redline, I'm just not sure what wieght to get I'm a newb still learning you know. I don't want anything too thick that it won't spool up fast but I don't want it do thin I gotta change every 10 days.
08-09-2012 04:07 PM
1971BB427 I switched to Brad Penn 15-40 as it's made with all the zinc old oils used to be made with. I get it from a local engine builder for $75 a case, which is less than the cost of other good oils and a bottle of zinc additive. I'm saving probably a couple dollars per qt. on every oil change.
I recently also found 30 cans (yes cans!) of NOS 20-50 Valvoline Racing Oil on Craigslist locally for $4 a qt., so I bought all of that too! Great oil at a very low price!
08-09-2012 03:13 PM
bigdog7373 I use regular autozone 10w30 with a bottle of zinc addtive (i think they call it break in oil). No problems at all.
08-09-2012 04:44 AM
75gmck25 15w50 Mobil One also has the right ZDDP, and its stocked by Advance Auto Parts and other parts stores. If possible, wait until Advance Auto has it on sale and offers five quarts of oil and a filter as a package for about $35.

Make sure its the 15w50, since its one of the few Mobil One oils that has the 1200 ppm phosphorous/1300 ppm zinc content.

Bruce
08-08-2012 09:19 PM
Mojo56 Be careful with racing oils as they do not have the same additive packages that are needed for street use.

Brad Penn is good... Joe Gibbs make many different oils to suit different applications.
08-08-2012 06:29 PM
Richiehd Brad Penn, The Green oil!
08-08-2012 03:23 PM
dave350v8 Im using 20/50 valvoline racing oil in my flat tappet sbc!
08-08-2012 11:34 AM
68NovaSS Search the board, there a a ton of ZDDP posts and thoughts.
08-08-2012 09:01 AM
rwa1015
zddp oil

I use Spectro Motor Guard 10w40(high performance racing oil) It was recommended by a local engine builder specifically for flat tappet cams and label says1800 ppm zinc and phosphorus I don't know any specifics on what is actually the best but this oil has worked for me and I plan to continue using it.
08-08-2012 08:13 AM
Hookedup12
What oil needed zddp

I have a 289 very low mileage I'm going to say 20-40 on new build I'm not changing the break in oil until 500 miles but after that what would be a good oil to use with a good amount of zddp

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:26 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.