Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Blown bbc too much crankace pressure
User Name
Password
lost password?   |   register now

Thread: Blown bbc too much crankace pressure Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-12-2012 10:24 AM
CNC BLOCKS NE
Quote:
Originally Posted by johnaiello View Post
First Thanks for the response.
Rings are all in correct, I assembled the motor, it has Manley stainless steel valves. Block was done at a very reputable shop. 95 lbs is what I have researched to be the correct compression reading with 114 lobe separation.The bore is stock 4.25, original forged aluminum pistons 8.75 compression. Sealed power E233K Moly rings. Harland sharp stud girdle. I took it to the strip and it ran bad too lean, I broke the #7 exhaust valve. I replaced the spring and I don't have a leak down tester but left the compression tester on each cylinder for at least 1/2 hour no loss of pressure.
Thanks For the help.
John
I can tell you a stock bore block once the heads are bolted on that 454 block distort alot and if you getting blowby I can see why. OEM block are frail compared to a Dart block.

Go over this link and you can see what I am talking. Putting boost pressure to the cylinders amplifies the poor block prep.

http://www.camaros.net/forums/showthread.php?t=58964
08-12-2012 09:23 AM
johnaiello
Block work

First Thanks for the response.
Rings are all in correct, I assembled the motor, it has Manley stainless steel valves. Block was done at a very reputable shop. 95 lbs is what I have researched to be the correct compression reading with 114 lobe separation.The bore is stock 4.25, original forged aluminum pistons 8.75 compression. Sealed power E233K Moly rings. Harland sharp stud girdle. I took it to the strip and it ran bad too lean, I broke the #7 exhaust valve. I replaced the spring and I don't have a leak down tester but left the compression tester on each cylinder for at least 1/2 hour no loss of pressure.
Thanks For the help.
John
08-12-2012 08:30 AM
454C10 I assume the engine is a low compression 454 with around 7.5:1 cr.

So, with a blower cam (wide lsa) and a later intake closing point from a bigger than stock cam, I would say 95-110 psi with a compression gage is about right.

Furthermore, compression gages are not known to be accurate. I have 2 gages that are the same make and model and one reads 20 to 30 psi more than the other one. But, the difference between cylinders is what you need to look for, no so much the number.

Maybe the header evac system isn't working or the rings haven't set yet??

Tell us about the block prep, pistons, and clearances used.
08-12-2012 07:48 AM
CNC BLOCKS NE Its best to do a leak down test at TDC. Is this an original bore block ?? How were the cylinders preped ?? Was it honed with a plate using a good hone VS a rinky dink one? What finish did they use on the cylinders?

No such thing as a chrom/moly rings and with any performance engine ring seal is key.
08-12-2012 12:54 AM
cobalt327
Quote:
Originally Posted by johnaiello View Post
I have a 454 HO crate motor, fresh rebuild chrome moly rings with 24 thousand ring gap,10/71 with (2) HP 4150 carbs, comp cam blower cam, solid roller lifters, roller rocker, I have moroso evac system from the breathers run down into the headers. I am pushing my dip stick out and pushing oil. when I put my foot in it it will blow the breathers out of the valve covers. Compression is 95lbs per cylinder. cam is a custom blower cam 650 lift not sure duration don't have spec sheet now, 114 separation. 400 turbo, 456 gear. I am stumped I don't want to run it and break any rings or worse. I NEED HELP Why all the pressure. Engine runs great doesn't smoke was broken in properly, plugs look OK still a little lean with 90 jets in back and 86 in front.

Thanks John
Are you positive you have "chrome moly" rings and not moly inlay or plasma moly rings or some other type of ring material?

In any event, upside down second rings will pump the crankcase nice and full of pressure.
08-11-2012 11:51 PM
johnaiello
Blown bbc too much crankace pressure

I have a 454 HO crate motor, fresh rebuild chrome moly rings with 24 thousand ring gap,10/71 with (2) HP 4150 carbs, comp cam blower cam, solid roller lifters, roller rocker, I have moroso evac system from the breathers run down into the headers. I am pushing my dip stick out and pushing oil. when I put my foot in it it will blow the breathers out of the valve covers. Compression is 95lbs per cylinder. cam is a custom blower cam 650 lift not sure duration don't have spec sheet now, 114 separation. 400 turbo, 456 gear. I am stumped I don't want to run it and break any rings or worse. I NEED HELP Why all the pressure. Engine runs great doesn't smoke was broken in properly, plugs look OK still a little lean with 90 jets in back and 86 in front.

Thanks John

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:12 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.