Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> using a 4L60E
User Name
Password
lost password?   |   register now

Thread: using a 4L60E Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-12-2012 10:23 PM
kalan thats not exactly true seen a site where a guy modified the valve body, and a few other mods I think. and its fully manual now. no electronic PCM control needed. seen a kit for a add on for a vacuum modulation, that controls pressure instead of PCM and throttle position. I just wondering if it will function for light driveing with manual shifting, without the electronic controls, PCM throttle position. or if it can be done using switches and appling the proper voltage to shift for temp use. tell I can get my 4L60 rebuilt. and upgraded. the 5 pinion sun gears,sun shell, new input housing that allows the use of the commerical red 9 disc alto kit with full thickness steels ( check Patc raptor trans.) and reverse drum for wider band use. and maybe the newer sprangs cann't remember if i upgraged them over ten years ago when I went throught it. with just the stock commerical kit 9 disc red alto's and real thin steels. just not long life with heavy hard use. quated as not for towing. used mine for towing and everything else. real hard use. not good for the thin steels in that kit. but like I said was wondering if it would function by manually shifting as it has the shift control. and its a 94 LT1 4l60E not the newer drive by wire models. and thoughs stand alone PCMs are starting at over 500 dollars the last red alto kit that I put in a relative 94 S10 blazer with uprgaded to v-8 specs was about 4 years ago and the full rebuild kit only cost about 250. why would I pay 500 for a stand alone PCM kit only to rip it back out later after rebuilding mine. the upgrade parts might cost more but i could just do another 9 disc red alto kit
08-12-2012 04:48 PM
bigdog7373 The e stands for electronic. You need the electronics. You can get a stand alone computer for it.
08-12-2012 02:50 PM
kalan
using a 4L60E

i was wondering will a 4L60E work, function, shift manually, drive, without the electronics hooked up. I have a 88 chev, with a 700R4-4L60 that died one first gear right now. but have access to a 4L60E, for real cheap. basically free to use till I can get mine rebuilt(part of a package deal on 2 LT1 motors with trans that bought in with a friend. he says just throw it in it should work just fine. nut I'm unsure and hesitant to do it if it won't function at all. but don't have a stand alone wiring harness or PCM mopdule right now. and might be a while before I can get one. this was a daily driver, that I need to get back on the road. and dont' want to strip it down for internal parts. ( not that I can't do it have rebuilt many tranny manual and automatic. and 700R4's to 4l60E's and one 4T60E. but want to use it later with the LT1 on a project vehicle with the freind (part street-drag car). any comments or thoughts could you manually control it using voltage inputs and switches. anyone got a good complete electrical wiring diagram. or know where i can get one or download it to see if it could be done.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:52 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.