Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> New to Hot Rodders site building 1966 Chevelle 310
User Name
Password
lost password?   |   register now

Thread: New to Hot Rodders site building 1966 Chevelle 310 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-13-2012 08:49 AM
Nicanor Thank you for the responses.

I don't want a blown motor because I want it to be a sleeper. I am looking into an AED 850, cam is .560/.565 and 243/251 at .050 duration. Compression is between 10.7 and 11.02. Will probably use Skip White's 383 stroker rotating kit but I can't get them to rerturn my calls so I started looking someplace else.

I have the TH400 and the 410 rear, intake manifold is currently a RPM Performer Air Gap but can be changed if necessary.

Thanks again,
Barry
08-12-2012 05:50 PM
bigdog7373 Op, if you really want 500hp i would go with a blown 355. You'll hit the 500 mark easily and driveability will be better since you wouldn't need a massive cam.
08-12-2012 05:24 PM
vinniekq2 I wouldnt go much past 10.5:1 either,single plane might give more top end,600 lift cam is probably correct depending on the air flow of your heads? I would use an 850 holley double pumper and 1 3/4"
primary tubes headers. the engine will need to rev past 6000 so you will need transmission and gearing appropriate to your useage.
08-12-2012 04:46 PM
bigdog7373 What are you thinking about for compression? You'll have to go decently high but i wouldn't take it past 10.5:1 if you want to stay on pump gas. I don't think you will hit 500hp. Not without using either race fuel of forced induction. I could be wrong, but 500 seems a bit wishful.
08-12-2012 03:05 PM
Nicanor
New to Hot Rodders site building 1966 Chevelle 310

I've read some post about the 383 stroker engine on this website and was hoping for some guidance.

I have a 350 block that was decked to zero that is .030 over. I'm going to have to go at least to .040 because the pistons currently slap.

So I have this block that is ready to go and another block that wasn't decked standing by.

I have the RHS racing heads 200 runner Pro action. I also have the RPM Performern Air Gap intake manifold, high flow oil pump and water pump. I will use an electric fuel pump.

I hope to use either the 383 kit from White Performance kit number 4340 with either flat top or domed pistons or a kit from Skip White part number P3832P-.040.

I talked with Lunati and they recommend a .600/.600 lift roller cam.

Its a lot of info but I am also trying to achieve over 500hp/tq and still don't have a recommended carb.

With the exception of the heads, no part has been bought so please substitute if it will help attain my goal.

Thank you.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:23 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.