Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Mustang II in 63 Rambler?
User Name
Password
lost password?   |   register now

Thread: Mustang II in 63 Rambler? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-14-2012 01:35 PM
timothale
$ 25 parts

One of the pick your part yards had a $ 25 all you can carry saturday
I filled a plastic tub with all the AMC parts plus extra odds and ends, used a seat belt strap around my shoulders . I did the conversion with 48 and earlier spindles, I saw amc brakes on a 30's I beam GM car, the guy cut off the spindle stub and ground the face flat.
08-14-2012 07:30 AM
farna All AMC spindles interchange. If you have an AMC car with disc brakes the entire setup will bolt off and bolt onto a drum brake upright. Just get everything from the caliper bracket out, including the spindle. Disc and drum brake spindles have different thickness bases, that's why the spindle is needed. In general dis spindles are thicker due to the different offset of the rotor/hub. You could space the drum spindle out if necessary, but most get the disc spindle.

The problem is parts availability. 79-83 AMC units are the ONLY ones I'd consider using. Some chain parts stores still have a source for the 79-83 rotors (calipers are easy to get for all), some don't. Last one I bought from Auto Zone for $55 two years ago -- Advance couldn't get one (AZ might not be able to now!). You have to go to an AMC parts vendor (yes, there are 3-4 out there!) to get the older rotors, maybe some antique brake parts vendors, and they are $100+ each. The Scarebird setup for $400 or less with current production parts is a lot better in the long run. If you need new rotors for a pre 79 AMC setup you've easily spent over half the cost of the Scarebird system. If you have a parts car with turnable rotors it might be worth using them, until you need rotors a few years down the road. Even the 79-83 should top $100 each in the next 3-5 years. The late model Scarebird parts will be available a lot longer, and right now they are using a $20 rotor. Buy a couple extra sets and store them!!

The AMC spindle on the 40 Ford upright with a Scarebird kit would be a reasonably priced disc brake upgrade. The only modification would be to the upright to the AMC spindle bolt pattern. Most AMC spindles are the same on the end, just different thickness to the base -- which can be spaced out or milled down. The exception is 75-78 models. Those used a big bearing spindle -- you want ANY 1952-83 Nash/Rambler/AMC drum or disc spindle EXCEPT 75-78. A Mustang II rotor will even fit the AMC spindle, but you'd have to make a caliper bracket to align the caliper over the rotor as the MII rotor has a different offset than the AMC rotor.

Speedway makes a 37-40 Ford disc brake kit that requires no modifications though -- and it's reasonably priced at $250. No point in spending that much on an AMC spindle conversion!
http://www.speedwaymotors.com/brake-...-b-p,4575.html
08-13-2012 08:50 PM
timothale
AMC bolt on's

I saw a conversion in a magazine using AMC Disc brake bolt on spindles on modofied 40's ford spindles. I did it but wish I hadn"t ruined a set of ford spindles . The disc brake spindles might fit your drum brake uprights.
08-13-2012 05:49 AM
farna The real question is WHY?? The 63+ Rambler suspension is basically the same as the Mustang II. It does have upper trunnion joints instead of ball joints (lower arm has a ball joint), but that isn't a problem. The upper trunnion rarely gives problems and it's easy to replace if it does. There are easily affordable disc brake options. Scarebird (Scarebird Classic Brakes LLC) makes one that will run about $400 with everything. The thing to remember is that ANY AMC kit will fit Ramblers back to 1950, all Nash/AMC back to 1952. There might be some minor mods, like a little grinding or spacing for clearance, but most need nothing. Aerospace Components makes a really nice four piston brake setup if you want to go show. Again, it's listed for AMX and Javelin, but I can guarantee you it fits the older Ramblers like yours. On the big Ramblers the spring towers don't get in the way of a V-8 installation (nor the 64+ smaller American, just 63 and earlier). They were made to mount the AMC GEN-1 V-8, which is close to the same size of a 396 Chevy or FE Ford. A big block will fit, though it will be a little tight. A small block has all kinds of room -- the AMC GEN-1 is sort of between the two in external size. The 64+ American won't take a big block, but will take any small block.
06-17-2012 11:10 AM
timothale
welder series .com

Welder series in canada makes weld it yourself hotrod parts and weld it yourself mustang II kits. even if you don't buy from them check out their web site, U tubes, instructions for their kits but applies to any front suspension installations.
06-17-2012 09:21 AM
mechdad1
Mustang II in 63 Rambler?

Hi to all I am sure this question topic has been beaten to death but I am looking at putting a mustang II front end in my 63 Rambler. Here is a cross member I found on ebay http://www.ebay.com/itm/MUSTANG-II-I...item2570eef2ac . I emailed them and they said I should only have to notch a little out of my fram rails to fit it in there. Any one have experience or opinions on this conversion. Have a few pictures posted under introduction forum

Thanks,
Randy

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.