Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> s10 rear end chop
User Name
Password
lost password?   |   register now

Thread: s10 rear end chop Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-17-2012 08:30 PM
S10 Racer I narrowed a 9" for my "89" S10 for 16" wide Hossier slicks, the frame ended up being around 24" wide, moving each side in about 8-1/2". You have to have the wheels and tires first to see how narrow you have to go. You will also have to tub the bed depending on how much backset your wheels have. Otherwise they will be sticking out past the bedside.
08-17-2012 07:47 PM
big gear head I just finished building a 9 inch for a customer's S10 about 2 weeks ago. The very first thing you have to do is get the wheels and tires that you are going to use and get them under the truck in the position that you want them in. Then measure between the mounting surfaces of the wheels so that you will know how wide the rear end needs to be. Then you can start on the rear end.

Narrowing a rear end requires some special tools. You must have a housing fixture to hold everything in line with the differential bearing bore. You also need very good welding skils.

The S10 has about 12 inches of room between the bed side and frame rail. To get a 14 inch wide tire under it you will have to move the frame rails in about 4 or 5 inches at least.
08-17-2012 04:02 PM
monster76 i would base my measurement off of a few things 1 being wheel width and offset to determine how wide the rear end will be and also you have to first decide how you want the tire to sit, do you want tucked in and slammed completely or do yo wanna have one those where the bed of the truck is a bit taller with the tire flush to the side of the bed. also your suspension will determine a lot also will you be running coil overs with 4 link or ladder bar leaf springs etc... there is alot of variables here
08-17-2012 03:37 PM
s10mikey
s10 rear end chop

would like some idea,s on how to cut a nine inch down for my 88 s10 and how narrow i need the frame to b for 14 inch wide slicks,, new to the narrow rearend game,,

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:06 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.