Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> mustang ii suspension on a 38 plymouth
User Name
Password
lost password?   |   register now

Thread: mustang ii suspension on a 38 plymouth Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-04-2012 06:07 PM
azteca48
Quote:
Originally Posted by dstinch View Post
Nice build. What air bags did you use. Are they on the same lower control arms in the other pics.
Thanks,
Don
Thanks, I used firestone bags. They are the same arms I just ordered the air bag kit basically you have to cut off the plate where the coilspring normally sits and weld on a new plate for the bag to bolt on. You can actually just make one out 3/16" plate. I can post some up close pics if you like.
09-18-2012 11:54 AM
alexleblanc nice build, i've got a 37 plymouth coupe and i've just ordered a similar setup from Helix. (coil overs instead of airbags.) I'm looking at your thread for inspiration and ideas.
09-06-2012 12:24 PM
dstinch Nice build. What air bags did you use. Are they on the same lower control arms in the other pics.
Thanks,
Don
08-26-2012 07:52 AM
timothale
suspension swap

My son has a 36 Ply coupe, I have 4 SBC in the shop and now he wants to install Mopar power. We have a couple stock MII suspensions, He has looked at a couple Mopars with M II suspensions,
For good instructions go the the Welder Series Site, they have excellent instructions They make weld it yourself parts, M II included and show how to install pieces in about any car proper fitting, alignment, etc.
08-25-2012 10:18 PM
azteca48 here is some updates on my build.
04-21-2012 08:54 PM
azteca48 Here's some more pictures
04-18-2012 05:32 PM
azteca48 Glad I could help Mariano. I spent a lot of time trying to figure this out. I will keep posting pictures as I complete this.
04-18-2012 03:25 PM
Anamayo Very good job Azteca, my name is Mariano and I'm from Argentina. I'm trying to adapt the front suspension of a Chevy (there is the nova), in a Ford 38 standard and your progress give me lots of ideas. thanks
04-17-2012 07:50 PM
azteca48 Getting closer I have the top hats fitted & ready to weld.
04-08-2012 08:58 PM
enjenjo I have done several Mustang installs on that era Mopar, looks like you are on the right track.
04-08-2012 06:58 PM
azteca48 After a lot of homework I found some pictures that show exactly what I'm trying to do. I made some box plates out of angled steel for the bottom. Now the crossmember will have something to weld to. I'm also going with stock spindles instead of the 2" dropped ones I had. I still have to cut and box the top for the upper arms.
03-05-2012 10:21 PM
azteca48 Just some pictures of some progress I have made. I started it last August.
03-05-2012 08:42 PM
matts37chev i think so
03-05-2012 08:34 PM
azteca48
Quote:
Originally Posted by matts37chev
I think I would take off the dropped spindles and move the crossmember up
that way you would not have to cut so much off of the top for the upper pieces
Thanks for the tip. Are you heading to the Portland swap meet next month?
03-05-2012 08:10 PM
matts37chev I think I would take off the dropped spindles and move the crossmember up
that way you would not have to cut so much off of the top for the upper pieces
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.