Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Shorty Headers with short or long collectors?
User Name
Password
lost password?   |   register now

Thread: Shorty Headers with short or long collectors? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-28-2012 05:35 PM
Cridder
Headman, Flowtec, Hooker, etc

Headman, Flowtec, Hooker, etc...these people must have stacks of dyno sheets and reams of info on exhaut systems, they can't share that dope with us cause it's gona turn into a war of numbers, well i geuss david vizard and hotrod magazine are gona save the day.
08-27-2012 10:42 AM
oldbogie
Quote:
Originally Posted by Cridder View Post
The headers for my 88 S-10 are 1 5/8" shorty's with a collector thats like 2 inch's long, i was thinking of extending the collectors out to 18" , i was thinking this mite act like an expansion chamber, maybe create a quazi long tube header effect and broaden the power range a little more off the bottom hopefully without hurtin the low end to much. any ideas? experience.
You are on the right track, the issue in this case is how to create and manage a returning negative pressure wave. Now be aware that no matter what you do you cannot duplicate the effect of full length tubes empting into a suitable collector; but by adding enough collector length to shorties so that the total length of the shorty and the attached collector is about the same as a set of long tubes with their collector. However in the case of the shorties with long collector the collector needs to either end into the atmosphere or into a large resonator box, so as to trip the return signal. However, given the signals will be diluted there will not be the hard pull from the exhaust on each cylinder at certain RPMs because that level of harmonic tune just won't be there. Keep in mind that long tubes do not continuously optimize this, the harmonic tune frequencies come and go with RPMs and they can be as much a negative element on making power at one RPM as they are a positive one at other RPMs. This is very apparent on raw dyno readings where the power is rising and falling within a band of general rising. Most of the dyno data you see published is smoothed; the real world is seldom like that. On a positive note, diluting out the signal peaks will tend to remove these up and down power excursions. For a street driven engine that sees most of its time in a moderate RPM range this stability can be a good thing for operating efficiencies at cruise rather than tuning to a peak power output at a high RPM that is seldom seen in normal use. The late model Ford Mustang gets by very well with shorty headers, thank you very much.
Bogie
08-27-2012 01:05 AM
Cridder
Talkin to jerry

Quote:
Originally Posted by vinniekq2 View Post
cridder,did you contact jere stahl? do you remember him?
That would reqiuere me (shiftworker) getting up before 4pm, checked out the web site though, some really good info.
08-26-2012 11:42 PM
vinniekq2 cridder,did you contact jere stahl? do you remember him?
08-26-2012 11:35 PM
Cridder
The long and short of it

From what i,'ve been reading collector length don't get much consideration, seems to be all about tube size, diameter of the primary's and the exhaust pipe.
1.625" Primary's and 2.5" pipe is good to like 5-550 horse.
I ran the optimizer in my Engine Analyzer +3.2 and it looks like long collectors help the mid a little bit at the cost of top end. long primary's on the other hand pay big dividends on top. I need a header for S-10 chassis thats got 41" primary's.
08-26-2012 09:36 AM
vinniekq2 contact jere stahl,they know more there about headers than anyone Ivetalked to before
08-25-2012 12:22 PM
cdminter59
Long primaries or shorty headers?

You need to read this article from Sanderson Headers so you can make a more informed decision. Let's get technical. The biggest controversy in header design is the "equal length" versus "shorty" styles - which is best?
08-25-2012 10:45 AM
bigdog7373 I dont think it will do anything. The long tube headers are better because of the longer primary tubes, not the collectors.
08-25-2012 02:02 AM
Cridder
Shorty Headers with short or long collectors?

The headers for my 88 S-10 are 1 5/8" shorty's with a collector thats like 2 inch's long, i was thinking of extending the collectors out to 18" , i was thinking this mite act like an expansion chamber, maybe create a quazi long tube header effect and broaden the power range a little more off the bottom hopefully without hurtin the low end to much. any ideas? experience.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:14 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.