Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Question about wires?
User Name
Password
lost password?   |   register now

Thread: Question about wires? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-31-2012 09:37 PM
raguza123 Thanks for the reply, I tested the engine out with the wires and it does run much better tahn it did with the copper core I had on there.
08-31-2012 09:12 PM
75gmck25 Analog VOM resistance readings are sensitive to the condition of the batteries in your meter, and whether its zeroed properly before you start.

Based on your measurements I don't think you have any bad wires, but only the manufacturer of the wires can tell you the normal range.

Bruce
08-30-2012 07:42 AM
raguza123
Quote:
Originally Posted by 67Mustang Al. View Post
You have a variation there for sure in your long leads but i dont think you will notice any difference between the two when they are installed. If you had a result like your copper readings then i would be concerned .
Al.
Could be my cheapo meter?
It's analog not digital
08-30-2012 07:31 AM
67Mustang Al. You have a variation there for sure in your long leads but i dont think you will notice any difference between the two when they are installed. If you had a result like your copper readings then i would be concerned .
Al.
08-30-2012 07:07 AM
raguza123 I did find a set, they had only one type Accel Super Stock radio suspression core, I know how much you all don't like Accel, I just found out they aren't made here, they were made in my home town back in the day when Echlin owned them.
Anyway new readings:
Coil lead 5,500
#1 31"long 11,000
#2 36"long 16,000
#3 31"long 9,000
#4 36"long 11,000
#5 26"long 9,000
#6 27"long 9,000
#7 23"long 8,500
#8 27"long 10,000
Are these Ok readings one I a little leary about #2 a little high
08-29-2012 01:44 PM
raguza123 I decided to replaced the set and put this set away should I decide to return to a points ignition system, I'll go with the type I used before I went to the solid core. it always ran good with them.
08-29-2012 11:01 AM
toddalin If you run low impediance copper wires, you may want to run a single spiral core (or resistance core) wire from the coil to the distributor. This was the warning on my Mallory HyFire System, and is what I did.
08-29-2012 08:06 AM
raguza123 I understand that when I went from a points ignition to electronic conversion, I needed to up grade my wires too, as the copper/nickel core which are like a 18 ga. wire would be better for points , an Accel tech said the performance would be better with carbon core wires.
There is very little resisitance with these wires, I'm running a Pertronix Ignitor Conversion kit with an Accel super stock coil(canister style) and a ballast resistor of 1.85 ohms
08-29-2012 07:32 AM
67Mustang Al. Hi there
Copper leads or copper wire, same applies.
Yeah the chart will give you very small readings for copper so if you know the diameter of the copper or AWG ( American Wire Gauge) it will give you fractions of an ohm, not much. From that chart 18 AWG copper has 21 ohms/ km so for a plug lead being 500mm long for example you would only have a fraction of an ohm or next to nothing showing on a standard workshop meter.
I guess if you have the wrong leads there is always ebay
Al
08-29-2012 06:58 AM
raguza123 Thanks Al, I just got off the phone with Accel, the tech claims that the copper core will not ohm out except that it will give me continuity only and that these ignition wires are ment for a points ingition system, I should be using carbon core wires.\, with my Pertronix ignitor system
08-29-2012 06:14 AM
raguza123 These are ignition wires not wires, vehicle wiring. Would it fall under the same as far as resistance?
08-29-2012 06:02 AM
67Mustang Al. Stealth 316 - Wire Resistance and Voltage Drop Calculator
This chart will answer your question.
Al.
08-29-2012 05:43 AM
raguza123
Question about wires?

I am using Accel Hi-Temp Super Stockcopper core 7mm wires and I am finding when I ohmed them out that from one end to the other end I am getting no ohms but a dead short, is this normal?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.