Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> Fixing Bent Running Board Brackets
User Name
Password
lost password?   |   register now

Thread: Fixing Bent Running Board Brackets Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-30-2012 08:49 AM
timothale
wood sandwitch

sometimes you can put a wood block top and bottom then use a big c clamp to hold it together then tweak on the Clamp. that way you dont bend the edge flanges. I have bent some C clamps doing this.
08-29-2012 11:37 PM
MARTINSR Here are a set of those brackets, they all look pretty different from one an other. A couple of these had some "ripples" in them too. I checked that against another set I have on a frame and those didn't have any so yes it appears they are not suppose to have them. I have to say it is very common for a part like that to have ripples in the metal as they were a quick stamping and not suppose to be perfect, just strong enough to hold a running board was all it was suppose to do. You can see that there is even a little twist in some of them.



But anyway, putting the running board on and making it level and all is really what matters. Are your bed and rear fenders on?

Brian
08-29-2012 09:32 PM
andrewakessler MARTINSR: You're correct. There are three different bracket sizes for each side. It looks like someone bent the hell out of them a long time ago (there are ripples on some of the brackets where they bent). I'd be more concerned if they held anything other than the running boards.

I'll definitely try both the crescent wrench and the pipe to straighten them.

Thanks to both you and enjenjo for the help.

-A
08-29-2012 07:29 PM
MARTINSR I am not sure they all should look the same. But if you bolt them to the frame and set the running board on them you will be able to figure them out. To straighten them, the more leverage the better, a long piece of pipe slipped over them you will be able to bend them like they are butter.


Brian
08-29-2012 07:16 PM
enjenjo Bolt it to the frame, and use a big cresent wrench to bend it back into shape. Make sure they are not made that way on purpose first.
08-29-2012 07:04 AM
andrewakessler
Fixing Bent Running Board Brackets

Working on a 48 Chevy Pickup.

While derusting my running board brackets, I noticed they were completely out of whack. Is there a proper (or improper; I'm not picky) way to straighten the brackets, or am I better off buying new ones?

Thanks,

-A

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:57 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.