Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> C10 fuel gauge issue
User Name
lost password?   |   register now

Thread: C10 fuel gauge issue Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-30-2012 04:12 PM
ChadGresham Oh yeah you have to watch what you buy off Ebay! Bought some LED bulbs for my truck once that were junk!
08-30-2012 07:36 AM
67Mustang Al. No i have not seen Dakota brand here in Aus. Just Speco and a lot of chinese made gauges that give poor readings. Ebay , out of Hong Kong , have buckets of gauges for the unwary.
08-30-2012 06:08 AM
ChadGresham I'm going to stick with oe replacements for my truck although i did custom install a sunpro super tach II in the dash that is doing pretty good. Since we are on the topic of gauges and instruments, ever come across those Dakota digital setups? Those are nice
08-29-2012 09:10 PM
67Mustang Al. Thats good then. Just check that when you get the replacement gauge it is compatible with the sending unit you bought. If the gauge is a direct replacement and not an after market x brand you should be good to go.
I am on my second oil pressure gauge (speco) and second tacho(speco) and travelled a thousand miles in total. Speco quality is better than my previous x brand which were made in a coal mine i would say.
08-29-2012 08:07 PM
ChadGresham Well that's good and bad.. I guess I've narrowed down my problem, however fuel gauges are not cheap. Thanks for the help though! I tried "C10 forum"but those guys were no where near as nice as folks on this site
08-29-2012 07:17 PM
67Mustang Al. AS the gauge is the only piece left to be checked and you have tested your grounds and continuity of the sending wire correctly, then it is most likely your gauge.
08-29-2012 06:09 PM
ChadGresham Ah now we are getting somewhere! I checked today and i have no power through the wire, so i checked at several points on the wire in case there was a break in it. No power all the way up to the gauge, so at this point it must be the gauge right?
08-29-2012 05:43 PM
67Mustang Al. If you have replaced it already i am not sure what to suggest, you will have voltage across the gauge as the sender is a variable ground. Check your ground tank connection by getting your test light and find power from your battery with the clip of your test light and touch the sharp point of your tester on the tank..The varying voltage from the sending unit makes your gauge go up and down as your fuel level changes.
This is how you can check your sending wire for voltage ( i think you said you had light here with your probe)
Checking for incoming voltage to the sending unit..........
Clip the 12V test light to a good ground on your car. (clean metal) Then back probe the sending-unit power wire. If the light glows with a bright light, the unit is receiving power; otherwise, the power source is disconnected. (where you puncture your sending wire for checking you can put a drop of superglue on the puncture)
08-29-2012 08:37 AM
ChadGresham At this point in time i do not have a working tester, only a test light. I have 12 volts to the gauge so should my test light pick up anything going to the sending unit? Right now when i unplug the sender the gauge goes to full and when i ground it out with the test light the gauge goes back to 1/8th of a tank...
08-29-2012 07:20 AM
67Mustang Al.
Testing gauge and sender.

Fuel Gauge Unit Test
This should give you some food for thought. You should start by testing your gauge so this should help you out.
V=I times R
where v= volts, I= current and R= resistance. (sending unit varies from empty to full so voltage will also vary if you use this formula.
08-29-2012 06:57 AM
ChadGresham thanks for the diagram, it's alot simpler than my Haynes manual. So judging by the picture should i have some voltage reading going to the sending unit?
08-29-2012 05:19 AM
67Mustang Al. With the float rising and falling in the tank it changes the resistance to the gauge. So when the float is high (full tank) there is low resistance and the gauge should show Full. You can test this with the sender out of the tank but you must ground the unit. Make sure your tank has a good ground.(use a second ground to check.) Normally the sender unit is matched with the gauge as a set or pair when new ,so if you have the correct replacement sender and you have made sure your gauge has a good ground connection ( add a second one to prove the ground connection from the gauge to battery negative.) the only thing left is a stuffed gauge.
the rusted fuel tank straps could have prevented a good earth as will painted metal. Clean metal gives a good earth.
08-28-2012 07:14 PM
C10 fuel gauge issue

My fuel gauge recently quit working and now sits on 1/8th of a tank all the time. So i dropped the tank and replaced my sending unit and while i was at it replaced the rusted fuel tank straps, painted the brackets and undercoated my tank. While i had the sending unit unhooked the gauge went to full but now with my new sending unit in and 10 gallons of gas in the tank it still only reads 1/8th of a tank. Wiring is good so is it my gauge?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:19 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.