Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> cant get the ac working after engine install
User Name
Password
lost password?   |   register now

Thread: cant get the ac working after engine install Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-01-2012 05:18 PM
LATECH Be sure the temp/blend door is closed and not heating up the refrigerated air as it passes through the ductwork. If all is well there then you will need to take a good hard look at the rear system.
I have found that the rear system tends to gather debris as the hoses are at the lowest point in the system, also expansion valves can stick, or fail for no apparent reason.
09-01-2012 05:11 PM
briansansone actually, i have an electric cooling fan pulling air. its about 85 degrees here right now.

i'll probably take it to an ac shop tuesday. it will have to be emptied before i can unearth the expansion valve.
09-01-2012 04:59 PM
LATECH 30-315 is still not right for a dual system. Do you have good airflow across the condensor? Cooling Fans working well?
30-315 still sounds like rear system not working right.
pressures should be more like 45-225 after system stabilizes (running for 5 minutes with recirculate on).
09-01-2012 04:59 PM
briansansone
Quote:
Originally Posted by LATECH View Post
White is the largest of tubes available at .072" inches.
The problem is most likely at the rear expansion valve. It is probably blocked or plugged, or is defective and is closed off, not letting freon pass, causing high side readings to be high, and low side to be low, and everything inbetween.
I would have to suggest opening up the rear at the expansion valve , both lines, and flush the lines, and replace the valve or orifice at the rear.


thats what i was afraid of. half the interior has to com out to get to the expansion valve.
09-01-2012 04:39 PM
briansansone yes i vacuumed the system for about 45 minutes. then i let it sit for an hour.
the gauges stayed at -30 vacuum.
09-01-2012 04:37 PM
briansansone I just checked again.

resting pressure now about 85

idle= 25 low 225 high
after 5 minutes= 30 low 315 high.

its not icing any more.
09-01-2012 04:36 PM
johnnyg Did you vacuum the system?
09-01-2012 04:26 PM
LATECH White is the largest of tubes available at .072" inches.
The problem is most likely at the rear expansion valve. It is probably blocked or plugged, or is defective and is closed off, not letting freon pass, causing high side readings to be high, and low side to be low, and everything inbetween.
I would have to suggest opening up the rear at the expansion valve , both lines, and flush the lines, and replace the valve or orifice at the rear.
09-01-2012 04:14 PM
briansansone the tube I put in was white. visually it looked the same. its definitely icing on the low side. and it will burn you at the outlet of the evap. I flushed everything except the expansion valve and rear condenser assembly. its ridiculously difficult to disassemble. I even considered bypassing the rear system.
09-01-2012 04:04 PM
LATECH Compressor is fine , as it is making 400 psi plus. Dont do that too much it wont be fine
Icing at the low side of the orifice means the orifice is plugged, or is way to small. What color did you put in?
Also, it sounds like the expansion valve in the rear (orifice if on an aerostar) is also plugged or not responding correctly.
Did you check / flush the rear lines and check the rear TVX device?
09-01-2012 03:27 PM
briansansone yes. and the sytem was pretty clean even before i flushed it
09-01-2012 03:18 PM
grandpa01 Is the orifice tube new?
09-01-2012 02:53 PM
briansansone yes the pressures are at idle speed.
125 psi with the engine off and the system equalized.
I replaced the accumulator.

The system calls for 68 oz. I have about 60 in there, and there is no change in temp. Its a van with rear ac.

The line just after the orifice tube at the evap inlet is freezing. but at the evap outlet it is super hot.
09-01-2012 02:38 PM
grandpa01 How much refrigerant and are these pressures at idle. Did you replace the drier?
09-01-2012 02:29 PM
briansansone
cant get the ac working after engine install

Well I'm trying to get my ac going again after adding a new engine.
I flushed the lines. added new oil, o-rings, seals, and an in-line filter.
I started adding refrigerant after evacuating the system, and the pressures were all over the place. too high, too low...... One minute the low side is 20 psi while the high jumps to almost 400. Then i'll turn it off, restart and the pressure is closer to normal. resting pressure is too low one minute and too high the next. Last check, which seems somewhat stable

low side at @50
High side at @ 150
resting pressure @ 125

Bad Compressor??

I am no ac pro...

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:05 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.