Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Never had a choice before.
User Name
Password
lost password?   |   register now

Thread: Never had a choice before. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-11-2012 10:01 AM
John long Good advice above Barry. Puller is better and a good shroud is priceless Good luck.

John L
09-11-2012 08:56 AM
BarryK Thank you guys, we will make a puller, now that I went to a short water pump and eliminating the clutch fan have more room in there then I have ever seen on a car and the original shroud is staying, so no problem there.
Since I put on the oil cooler and went to 0w30 mobil-1, cooling has never been an issue with this car, where before after I built the engine, if ran on expressway for an hour, when you hit a town, it never over heated but temp would climb 20-30 degrees, for first 15 minutes in city driving and then go back to normal.

Thanks for the advice.
09-10-2012 02:24 PM
OneMoreTime Fan should work either way..the critical piece is the shrouding and also look at how air is directed to the radiator for a good airflow..Shrouding can be easily fabricated from aluminum flashing material that can be found at the local building supply. use pop rivets or the body panel glue to assemble the shroud. Most aftermarket fans come with a generic kind of shroud/mount that can be incorporated.

Sam
09-10-2012 02:15 PM
cdminter59
Never had a choice before.

Leave the coolers mounted in front of the radiator and mount the fan on the other side. Make sure you have a good shroud too. If the fan has the cfms stated you should not have any problems with overheating.
09-10-2012 12:44 PM
BarryK
Never had a choice before.

On my 454 C-3 I'm converting to a serpentine setup and what I have at the moment is an oil cooler and a transmission cooler mounted in front of the radiator.

I have found a 17" 3400 cfm (pusher or puller) fan that will replace the mechanical fan.

My question is what if I moved the coolers to the inside of the radiator and mounted the fan as a pusher? (not room for fan out there also)
OR do I leave as is and mount the electrical fan as a puller on the inside of radiator.

I have always been under the impression, pushing was best but I really don't have a clue.

How would you do it?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:20 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.