Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 75 Monte Rear End
User Name
Password
lost password?   |   register now

Thread: 75 Monte Rear End Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-11-2012 12:43 PM
vinniekq2 You might consider buying a complete 12 bolt to swap in.There are companies that sell complete units with w/e gear set you want.If not cheaper its certainly faster.The monte carlo my friend Mike had came with 2.73 gears. We used that rear end until we put a bigger cam in the engine then bought a complete diff. A posi is essential or you will spit spider gears and burn 1 tire out regularly.The car cannot use a 3k stall converter with out a posi,,,
09-11-2012 11:21 AM
big gear head Your car probably has something in the 2.73 to 2.41 range. This isn't good for what you want to do. A 3.73 with a 700R4 or 200 4R transmission would be good. There is no way that you are going to get better performance and keep the gas mileage without using an overdrive transmission.

Swapping the gears is going to require a 3 series differential. If you ahve a 2.56 or 2.41 gear then you have a 2 series and it will need to be swapped. I recommend using a Yukon Dura Grip and a set of Yukon gears and installation kit. This will get both wheels pulling so that you are not just spinning one wheel. The Dura Grip is not that expensive and it works well. There is a member on this sight that is a Yukon dealer. Prostreet6t9 can help you with the parts.

You must know how to set the pinion depth, bearing preload and backlash to set up a set of gears. You must be able to read the contact pattern so that you wil know what adjustments need to be made to the pinion depth and backlash. Changing gears is not a bolt in job. It requires shims and patients.
09-11-2012 10:54 AM
david-b I wanted to bring this thread back from the dead since it's my thread and I'm expanding on it.

It looks like I want to get the gear swap done. It feels like the car takes too much throttle in order for it to move. Feels like the power is there at the motor but it's not transferring to the wheels like it should be.

So my question is, what would be the best gearing for me? Was recommended 373-410, but what would be good for getting the power down AND still be good on gas mileage? The car will see some track time but it's a street car, so want good driveability. Again, I have a 3500-3800rpm converter.

Next, does having a POSI make a real difference for street cars? Is it worth the extra money?

I'm pretty sure going to have a shop do the install. What I would like to do it drop the rear end before winter gets here, and then get the whole thing powdercoated and cleaned up. Then take it to a shop to get the gears swapped. Do places do that or does the rear have to be on the car in order for a shop to do it?

Thanks in advance!
09-21-2011 12:23 PM
SSedan64 Yukon has good quality parts. Their Master Install kits come with Timken Carrier & Pinion bearings & Super Shims. Shop around for best prices.
09-21-2011 06:42 AM
david-b Hmmm, looks a little difficult. I'll probably just have a shop do it

Any recommended brands on gears or anything else I need to know?
09-20-2011 10:43 AM
SSedan64 It can be done by a 1st timer but, can be quite a tedious job if you've never done it. Also requires a few special tools and close tolerance precision work.
Look thru these links & see if you want to try & tackle it, if not let a Shop do the work

Some very good Gear Swap Info:
http://www.hotrod.com/techarticles/d...install_guide/
http://www.thirdgen.org/techboard/tr...axle-gear.html
http://www.yukongear.com/Downloads/M...structions.pdf
09-20-2011 08:55 AM
david-b
Quote:
Originally Posted by SSedan64
75 Monte came with the 8.5" 10-bolt, a very strong Rear.
If your Cam requires that much stall a 373-410 gear would be better.

The larger Cam moves the engine's power band to a much higher rpm, so you need a numerically higher gear ratio to optimize acceleration.

An O/D Trans would give you the best of both worlds, use 3rd in the 1/4mi and O/D for cruising.
Thanks for the info.
Do the gears literally just swap right out? Or does the whole back have to drop and replaced? And what other mods would need to be done in order to make new gearing work properly?
Again, totally new to the rearends right now... so sorry for the nOObie questions. I do appreciate the help!
09-20-2011 08:36 AM
SSedan64 75 Monte came with the 8.5" 10-bolt, a very strong Rear.
If your Cam requires that much stall a 373-410 gear would be better.

The larger Cam moves the engine's power band to a much higher rpm, so you need a numerically higher gear ratio to optimize acceleration.

An O/D Trans would give you the best of both worlds, use 3rd in the 1/4mi and O/D for cruising.
09-20-2011 08:14 AM
david-b
75 Monte Rear End

A guy mentioned to me that I should consider switching out rearends on my Monte. I've heard this before, but I'll be honest, I know nothing about the gear ratios here, so looking for some help and recommendations.

Firstly, does anyone know what the gearing is on this car? It's a stock 10-bolt with a TH350 auto.

Due to my larger cam, I had to go with a 10" conveter (3500-3800rpm). I know this comes into play with the gearing, but why?

Lastly, what would you recommend? Car needs to be streetable, but will see some track time next year. Looking to keep power, and good drivibility.
Thanks
/D

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:42 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.