Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Solvent pop quick fix needed
User Name
lost password?   |   register now

Thread: Solvent pop quick fix needed Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-08-2012 09:25 PM
302 Z28 The problem with wax & grease remover is people do not know how to use it. It must not be allowed to evaporate dry, it must be wiped dry. FWIW Ajax and Comet are two completely different products. Comet would not be advisable to use in prep work IMHO.

10-08-2012 06:55 PM
kmoses I sanded the fender until the craters were gone starting with 220 and finishing with 500 wet. Using a grey 3M pad and Ajax I washed the fender and then rinsed with water twice and let it air dry overnight. This afternoon I sprayed both fenders with Nason Ful-Thane Holly Red and other than a few dust nibs they were glassy smooth and crater free! Thank you for all the help.
10-04-2012 11:13 AM
cyclopsblown34 I've had the same problem with Nason Epoxy primer and what Milo said is what I've had to do to resolve it. Since then, I just use SPI epoxy primer.
10-03-2012 10:31 PM
paint dude Be careful when using ajax,comet etc. Be sure and rinse WELL these products tend to leave a film behind and if you dont rinse it you will have delamination problems, Wax and grease or a good waterbase cleaner will do a great job.
09-13-2012 08:18 PM
milo It can cause more problems than it solves..
This time just "dust" on a "ground" or mist coat at first and then once it is showing good behavior put it on wetter etc...
no primer if it's nice and flat
09-13-2012 07:56 PM
kmoses So sand again, clean with Ajax and grey scuff pad, rinse well with water, when dry spray with primer. Is it the wax and grease remover causing the problem?
09-13-2012 06:55 PM
Originally Posted by kmoses View Post
wiped with wax and grease remover
If you take the wax and grease rmover out of the loop and use Ajax on a grey scuff pad and a clean water rinse, odds are you won't see the fisheyes again.
09-13-2012 05:52 PM
kmoses I sanded the fender down until the craters were gone, wiped with wax and grease remover, sprayed one nice even coat of nason epoxy primer and the craters are back in what looks to be the same locations! What am I dealing with and how do I fix it? The rest of the car has been no problem, just this one fender. Is there any way to fix this other than a can of aircraft stripper and a putty knife?
09-13-2012 05:22 AM
Irelands child You have a 24 hour window with Nason for recoat and cross linking of the chemical components (at 72*, less if higher if I recall) - it's probably gone now. My thoughts are that you possibly have polish/wax or other chemical (WD-40? Teflon spray? etc?) problems rather then solvent pop. I've only used the Nason epoxy once - disliked it. Resand with 320-400 wet, removing the craters and recoat.
09-13-2012 01:01 AM
tech69 When did they appear? Was it some time after flash time or right away?

If it's right away that could be contaminants.

I never had solvent pop on Epoxy but if it's a dozen small holes why not block it out and spot in some epoxy? It's not much more work and you wouldn't have to wonder about that area and how it will hold up. If it's a reaction and not solvent pop then sanding it down will just give you the same problem again cause it will re-reveal that stubborn area that gave you problems to begin with.
09-12-2012 09:14 PM
Solvent pop quick fix needed

I just sprayed Nason epoxy on a fender and did not allow enough flash time between the three coats. There are about a dozen small craters. Can I fill these with metal glaze, block the fender, apply another light coat of epoxy and then spray color? Or do I have to sand it all off and start over?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:12 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.