Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Blowing fuse(s) at ign/acc at fusebox
User Name
Password
lost password?   |   register now

Thread: Blowing fuse(s) at ign/acc at fusebox Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-24-2012 05:59 PM
EOD Guy Rock on Bro!
10-24-2012 12:19 PM
64Joker
EOD Guy

I installed the new dizzy module and module power surge protector, tested good at 12v and engine started with no electrical issues!
Tested the new electrical fan toggle switch setup with no issues there!

I'm guessing that the initial issue was caused due to a incorrect wiring configuration at the electrical fan toggle switch wiring which caused a spike to the dizzy module which blew the module!

Ready to "Rock n Roll"!

Thanks for all your help forum!
10-12-2012 09:27 AM
64Joker
EOD Guy Info

FYI...

Mallory now carries a "performance power filter" that will protect the module, it cost about 45 bucks, probably well worth it!

http://tinyurl.com/8z2dub3

I'm gonna order the new module and protector today, I'll let you know when I get the engine started! Thanks for all your help, it's appreciated.
10-11-2012 04:49 PM
EOD Guy If you have 12v to the dizzy during crank and run, that'd be my guess...... I keep a spare module in my car...... seems I blow one every other year or so.....used to get me stranded, now that's the 1st thing I ck/change...... accel has them for about 40 bucks, but they arn't the best QA, IMO. The OEM chevy ones are expensive but the QA is much better..

BTW glad you got it figured out.
10-11-2012 01:14 PM
64Joker
Follow-ups

I'm back to the grind after a 2 week vacation in New York!

I replaced the voltage regulator and capacitor, I'm no longer blowing fuses when ignition switch is turned to "on" or "run/start". Attempted to start engine, it cranked but did not start.

Executed 2 tests on the Mallory distributor module, but it failed! The volt meter displayed a continuous variable reading on both tests (sensor unblocked, then blocked). Time to replace the module?!
09-30-2012 11:01 AM
64Joker
To: SSedan64

Quote:
Originally Posted by SSedan64 View Post
..
Does your local Auto Store test the Module with Distributor installed in engine or just need the Module mounted in the Distributor??
Took my Module to AutoZone & they tested it without Distributor.
The auto stores in Nor Cal (Northern California) will test your mod out of the distributor, however they advised that my specific "Mallory" mod would not qualify for their test machine, thus I will have to execute my own mod test once I resolve my electrial issue when I get back to California next week.
09-23-2012 02:37 PM
EOD Guy I would NOT start it untill you corrected the reg problem..... voltage spikes reek havoc on elec components. Odds are that's your problem.

If I were you I'd look at how much the reg costs vs a new internal regulated alt. Super easy to convert to the new alt..... basicly you install two jumpers at the old reg, add a 8-10 gauge from the alt back to the orig factory splice (to handle the need increased amps) and change out the pig tail.

Best thing I ever did for my car..... up till I re-wired it with a modern wire/fusebox kit.
09-21-2012 10:33 PM
SSedan64 Unregulated Alt output may damage the Module.

Reg Info:
Catalog
Catalog

CHEVY MAIN ELECTRICAL :
Catalog

Does your local Auto Store test the Module with Distributor installed in engine or just need the Module mounted in the Distributor??
Took my Module to AutoZone & they tested it without Distributor.
09-21-2012 10:37 AM
64Joker
EOD Guy - Follow-up

I have an "External" alternator original setup:

As suggested, I unbolted the volt reg from firewall, removed the ground, then reconnected the hot wire harness and the ign fuse did NOT blow.

After removing the volt reg, I inspecting the back of it and it looks pretty darn corroded and rusted!

So, it wouldn't be that expensive to replace the volt reg at this point.

Question:
Would it make sense to test the HEI dizzy module at this point. Would it be a valid module test without the volt reg installed, or should I wait to run the module test after replacing the volt reg.?
09-20-2012 07:31 PM
EOD Guy OK you're getting somewhere........ One question, do you have the orig alt or a new internal regulated one?

If it's the old alt...........the voltage reg has a ground via the housing base and a wire (if I remember correctly)........ unbolt the reg from the fire wall and disconnect the ground wire (if it has one) reinstall the hot wires and see if you still pop the fuse....... if you don't..... I'd guess the reg has gone south. Now if it were me I'd put a new internal regulated alt on it and do away with the old reg. You can leave it bolted to the firewall and hook dummy wires to it, if you want the orig look etc...... In my 67 I did the swap and it solved all the dim, blinking headlights, tail light problems, heater etc...... and the reg problem.....lol
09-20-2012 06:41 PM
64Joker
EOD Guy: Follow-up Part II

Not sure disconnecting the voltage regulator proves anything at this point (other than I'm not blowing the ign fuse anymore. But with the voltage regulator disconnected, can I perform a HEI dizzy module test now?
09-20-2012 02:19 PM
64Joker
EOD Guy: Follow-up

Here's a recap of what tests I've performed so far:

1. removed ign module to have it tested, however every auto store and auto electrical shops (most reputable ones) said that after market modules can only be tested while module is installed in the dizzy. The module test machines they have can only test stock type modules! I can not test the mod unless the car is not blowing ign fuses!
2. The wires to the "S" and "R" starter/solenoid check good for continuity via multimeter and physical appearance.
3. Removed the ignition switch and noticed the housing was a little loose, so I removed it, inspected it for burnt wires, all looked good.
Re-Installed the ign switch, tightened the housing real good and the engine began to crank now, but it was still blowing the ignition fuse.
4. Physically inspected all other wires, under dash, connected a 12v light to ign fuse connection and went through disconnecting most everything I could track down to see if the 12v light went off while in ign switch start position, no positive results.
5. I removed the 4 pin connector to the voltage regulator and noticed that the ign system no longer blows the ign fuse while the ign switch is turned to the "on" position and the engine still cranks (but of course the engine will not start due to the voltage reg being disconnected). Is this a valid test to warrant replacing the voltage regulator? Not giving up yet!
09-15-2012 04:38 AM
EOD Guy It's all good.
09-14-2012 08:17 PM
64Joker
EOD Guy

My apologies EOD Guy!

Yes, the previous posts are all related.
I did previously disconnect all of the fan and toggle switch connections as suggested and replaced the blown 20 amp ign fuse, but the new fuse blew also.
I will follow-up with your other suggestion with the "starter crank wire".
Thanks for your patience, I will try to keep future posts in line, I'm just getting a little frustrated with not have more electrical knowledge.
09-14-2012 07:25 PM
EOD Guy I assume this is the same problem as in your other 3 posts?

You will prob get a better answer if you state everything that led up to the event of it not starting...... ie..... you installed the elec fan.

Somethings got a direct short

I'd start at the starter crank wire or "S" terminal, netural safety switch if it isn't them, then i'd unhook your toggle, relay, fan setup and see if that allows you to crank it. If that doesn't work, try unhooking your dizzy pwr and see if it'll crank etc... when you get it to crank, hook the dizzy pwr back up etc......
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.