Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Saginaw 4 speed question
User Name
Password
lost password?   |   register now

Thread: Saginaw 4 speed question Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-18-2012 11:36 PM
junior stocker Think about using the MOPAR A-833 trans made for Chevy/GMC trucks. It's basically Chryslers HD 4-speed trans regeared so 4th is actually overdrive. Uses a Hurst shifter and all. You can beat on it like an Army Mule, but not on a Saginaw for very long; especially in a heavy truck. Butch/junior stocker.
09-18-2012 04:22 PM
Gearhead forever
Quote:
Originally Posted by boothboy View Post
Now a days with the gas prices being what they are and what they will probably be I'd be looking for a gear box with over drive. A nice 5 or 6 speed.
BB
I agree, but the trouble is that I dont have the coin. I need to finish this project on a shoestring. If you can recommend a 5 speed that isnt any weaker than the Sag, and wont kill my pocketbook...I'm all ears! Tell me its possible....
09-18-2012 10:13 AM
boothboy Now a days with the gas prices being what they are and what they will probably be I'd be looking for a gear box with over drive. A nice 5 or 6 speed.
BB
09-18-2012 08:08 AM
RWENUTS As long as you don't put the loud pedal on the floor and sidestep the clutch pedal you should be fine.
After all the factory put a 4 speed o/d based on the mopar a833 in them.
09-18-2012 06:44 AM
Gearhead forever ARGH - WHERE IS THE EDIT BUTTON??

I meant to say I'm NOT planning on abusing this transmission! OOps
Realistically, it will never likely even see 300 hp.

Thanks for your responses
09-17-2012 06:15 PM
39 chev I used a saginaw in my 69 C-10,Iwas running a fairly stock 350 in front of it. I got the transmission out of a Vega.It had the shifter bolted to the floor in the Vega,so I did the same in my truck. The trans will not take much abuse,but I pulled a camper with mine,and it was a big improvement over the "three on the tree" that the truck came with. In answer to your question,The saginaw would not be a good choice for you. By the way the trans ,shifter and console cost me $20.
09-17-2012 07:51 AM
RWENUTS If it is a saginaw the shifter arms are all on the side cover. If you're real good at tranny swappin' then put it in. Cause if you abuse a sag you'll be swappin' in another one shortly. THey don't take any abuse at all. A low performance tranny.
Spend the money, do it right, put a muncie or BW T10 in it.
09-17-2012 07:22 AM
timothale
close ratio

The transmissions have different internal parts, gears, that determine the speed for each gear at a fixed rpm. lighter cars, corvetts, use to have optional 2. 20 first gears and larger cars had (I thinK ) a 2.54 first gear, With a close ratio you would want a lower geared rear end, with a close ratio the RPM didn't change as much between shifts keeping the engine in the max power band. If you have a close ratio in a truck, with a higher geared rear end ( In the 2.xx's) you will have trouble hauling a heavy load with out burning the clutch . With 4.56 rear gears , a 2. 20 would have enough torque to pull. but you would be running higher RPM's at highway speeds.
09-17-2012 06:31 AM
Gearhead forever
Saginaw 4 speed question

I want to put a 4 speed in my 87 chev shortbox behind a 5.7L. I've located a gear box that is a close ratio but I dont know what that referrs to. I'm planning on abusing this transmission terribly so I figure it will be ok behind a 300-350 hp engine....no?

Any advice on buying and installing one of these would be great. I need to know what to look for in a belhousing, flywheel and clutch assy...

thanks in advance

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:32 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.