Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 8.8" Ford axle question...
User Name
lost password?   |   register now

Thread: 8.8" Ford axle question... Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-28-2012 09:56 AM
S10xGN Thanks guys! I'll be keeping this thread for reference.

09-27-2012 01:37 PM
big gear head If you are using Explorer brakes then you will probably need the 7750 housing ends. The 8.8 and 9 inch 31 splines are the same. Yes, Moser will make the axles with 31 splines and make them fit the press on 9 inch Ford axle bearings. Tell them what brakes you are using and they will make the axle hang out fit those brakes. Just be sure that you cut the housing correctly so that the axles fit. If you cut too much or not enough then the axles will not go in all the way or there will not be enough splines in the axle gears.
09-27-2012 08:43 AM
S10xGN I would most likely keep the Explorer brakes or upgrade to Mustang stuff. I really just wanted to eliminate the C-clips without using a (leaky) kit. So, I can add the Moser #7700 9" ends after narrowing and then spec custom axles with the 8.8" splines and 9" bearings?

09-26-2012 08:28 AM
big gear head Moser makes housing ends for the 8.8 that use the press on 9 inch Ford axle bearings and the stock Mustang 8.8 brakes. They also have housing ends with all of the 9 inch Ford brake patterns, so there is a large selection. If you think you might upgrade the brakes later on then using one of the 9 inch ends would be a good idea because there are so many brake optinos for the 9 inch Ford. Have the axle hang out set for the housing ends and brakes that you will be using. Moser knows what these are, so they can be a big help in making that decision and getting the measurements right.
09-26-2012 07:58 AM
9 ends.

Ford used 3 different ends on the 9 rears, one of the patterns is the same as the 8.8
09-26-2012 07:46 AM
lmsport You would need custom axles.
Moser is the cheapest and they're easy to deal with.
It does take some fairly accurate measurements but a good tape measure will do the job.
To reuse the existing brakes you just have to make the new axle have the same offset from the braket or backing plate.
09-26-2012 06:23 AM
8.8" Ford axle question...

Hi All,

If I were to have 9" ends installed on a 31 spline 8.8" axle, what would I spec for axles? Does a standard 9" axle fit the 8.8" side gear splines? And if this were done, would standard 8.8" brakes work?



Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 07:34 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.