Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> TH 350 cooler line oil flow
User Name
Password
lost password?   |   register now

Thread: TH 350 cooler line oil flow Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-28-2012 12:41 AM
jeepers creepers
Quote:
Originally Posted by Crosley View Post
Design of the trans pump , stator and input shaft... With wear on the bushings and shaft, the oil takes the path with least resistance, so oil flows out each port with nothing attached.


With a cooler and lines installed , the oil is pushed the correct path.
You made me an happy man for today, thank you!
By the way , tranny has been freshly rebuilt and i changed as weel all the bushings.
09-27-2012 06:17 PM
Crosley Design of the trans pump , stator and input shaft... With wear on the bushings and shaft, the oil takes the path with least resistance, so oil flows out each port with nothing attached.


With a cooler and lines installed , the oil is pushed the correct path.
09-27-2012 08:37 AM
cobalt327
Quote:
Originally Posted by jeepers creepers View Post
Thank you, that's what i've thought so i put my finger on the return/in line to see if it has any pressure but i can easily stop the flow, in the other line has a little bit more pressure , i hope that's enaugh to create a flow in the circuit cooler otherwise it's a problem.
The bottom cooler line from the tranny going to the cooler should have around 20 psi cold at idle speed. Up to 45-55 psi revving it up.

You can check the pressure before and after the cooler(s) to see if there's excessive pressure drop.
09-27-2012 07:29 AM
jeepers creepers
Quote:
Originally Posted by SSedan64 View Post
The Bottom line is the Feed/Out which has pressure.
The Top line is Return/In, it doesn't have suction so some fluid may flow out there.

Radiator with side tanks:
Bottom = Feed/In from bottom Trans line.
Top = Return/Out to top Trans line.
Thank you, that's what i've thought so i put my finger on the return/in line to see if it has any pressure but i can easily stop the flow, in the other line has a little bit more pressure , i hope that's enaugh to create a flow in the circuit cooler otherwise it's a problem.
09-27-2012 06:14 AM
SSedan64 The Bottom line is the Feed/Out which has pressure.
The Top line is Return/In, it doesn't have suction so some fluid may flow out there.

Radiator with side tanks:
Bottom = Feed/In from bottom Trans line.
Top = Return/Out to top Trans line.
09-26-2012 02:44 PM
jeepers creepers
TH 350 cooler line oil flow

TH 350 gurus, i need your help, while i was working on the fluid cooler lines, i didn't remember what was the cooler feed oil/out for the cooler so i started up the engine to see from where the fluid is supposed to come out , ATF was coming out from both lines!, way more from the lower port (wich is supposed to be the right one) but also a little bit from the "return line".
Transmission was in N, don't now if this weird flow happens also with the shifter in that position , i have to try in P but now i'm concerned about something wrong in the oil pump assembly, may be that i forgot a checkball in somewhere during the rebuild?
Trans is freshly rebuilt and got a TransGo shift kit on it.
Any help will be apprecciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.