Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> morris minor- s10 frame ??
User Name
Password
lost password?   |   register now

Thread: morris minor- s10 frame ?? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-01-2012 11:04 PM
406 bug As Brian stated, after all is said and done, building from scratch is best. Look at my bug Pics, may provide some ideas. All round tube crome moly.
10-01-2012 07:45 AM
MARTINSR I liken it to putting an S-10 fender on the Morris Minor, would we try that? It CAN be done with enough modification. But making one from scratch would be easier.

Brian
10-01-2012 07:23 AM
timothale
Frame Swap

I'll never do another frame swap unless I actually closely examine one somebody else has done. Years ago I put the 48 Jeepster (4 cyl 2 WD) on a 4 x 4 Jeep truck FC 3/4 ton Chevy V8 power, chassis. That one was easy, the frames both had the same contour, the truck was longer in the rear and longer in the front. I used a later GM P/S gear box. Popular swap for Jeeps. The big tires stuck out but the wheel base was the same. fast foreward 20 years My son started to get the jeepster back on the road, It needed a total brake rebuild, Minimum parts cost about $ 500, Then we saw a longer nose 53 pickup at a car show on a blazer , the kid said it was easy. I found a rusted blazer with 8 wheels, 4 good big tires, no engine for $ `150. We sold the 4 X 4 Jeep chassis with an OD conversion for $ 300, the scrap iron body parts for $ 50, sounds good so far. Then the fun started, to get the engine to fit with the rear axle lined up we had to move the engine, trans, T case, back 8 inches, New motor mount brackets, trans mount, new Front and Rear drive shafts, New steering shaft, New mounts for the clutch and brakes, new mounts for the E brake, Relocate the rear shock crosmember, rebuild the rear seat floor pan to clear the frame contour. Neither the blazer or jeep gas tank would fit, new rear bumper and trailer hitch, the front axle is an inch or so foreward from the jeepster location but that gives more clearance for big tires , and the longer front frame gave a good winch mounting areas.
09-30-2012 10:31 PM
MARTINSR It will take WAY more than simply "shortening" an S-10 frame. It takes PILES of fabrication to use the wrong frame under a car.

Brian
09-30-2012 08:55 AM
nybronc
morris

i'll have to check that out at jegs ,from what i've read a s10 works if shortened, didn't read were width was a issue, what did the jegs frame kit include ?
09-29-2012 03:21 PM
Crosley I've got a 1962 Morris Minor 1000 2 door car about 15 feet from me... I dont see a S-10 fitting width or length.

It is a steel S-10 frame , so it can be cut n welded.

I bought a chassis kit from Jegs with roll cage for my Morris.. a straight axle will under the front, 4 link drag style suspension in the back end
09-29-2012 02:17 PM
delawarebill
m/m nice

don't know of the fit.. i had a '59 van.. or what ever they call the truck like body.. matter a fact i just saw a sedan (car) among a bunch of Mg's not far from me... nice proj u got...
09-29-2012 12:02 PM
nybronc
morris

building a street car, strip once in a while coupe, poss. straight axle, if so down the road some, try it with front coils first.
09-29-2012 11:49 AM
timothale
what's the plan.

From My experience most swaps are not as easy as you are led to believe. What are you going to build?, Drag race gasser,?/ street car with newer engine , ? auto cross ? funny car tilt up body?.
09-29-2012 10:59 AM
nybronc
morris minor- s10 frame ??

anyone have any insight on putting a morris minor on a s10 frame ?, like to do it , track similar on both vehicles ? i think the frame needs to be shortened a bit,any input would be a great help. thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:01 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.