Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Basecoat and primer coverage question
User Name
Password
lost password?   |   register now

Thread: Basecoat and primer coverage question Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-03-2012 06:42 AM
oldBodyman "I didn't use hardner. So what problem would that cause? I don't see any issues right now and I have already wet sanded the entire car."

The hardened epoxy sealer, the un-hardened base coat and the hardened 2K will absorb the solvent from your repaint at different rates and then shrink-back at different rates, commonly called 'bull's eyes'. The solvents can also 'fry' the edges of your sand-thrus.

"Also, your answer was informative but did not say whether to use white epoxy or not. I assume you meant that it doesn't matter as long as you get complete coverage. Is this right?"

IF it covers in 3 coats great, just spot it in and continue the repaint

IF it takes 5-6 coats, tint the sealer to a very light gray, white's too bright and gray is too dark. Watch out for over-spray.

IF it's a monster and takes 10 coats or more to cover, sand it all off, seal it with very light gray and re-do it all. Sorry but the spot repairs WILL show thru within a few months and you will just love it when they do.
10-03-2012 05:06 AM
off2wildblue I didn't use hardner. So what problem would that cause? I don't see any issues right now and I have already wet sanded the entire car.

Also, your answer was informative but did not say whether to use white epoxy or not. I assume you meant that it doesn't matter as long as you get complete coverage. Is this right?

SAM
10-02-2012 11:47 PM
oldBodyman "So should I spray white epoxy as a sealer over the gray high build patches or just spray yellow base to cover? "

Yellow can be a bear for coverage, some will cover in 2 coats, others will take 15 coats.

Get a sheet of plate glass and spray the whole plate with your base. Take a sheet of cardboard and mask off 3/4" steps for each additional coat. Let it dry and hold it up to the light to see how many coats it takes to cover COMPLETELY.

I do hope you used hardener in your original basecoat, if not it may be easier just to wet sand it all off and start over.

Good luck with it.
10-02-2012 07:27 PM
off2wildblue
Basecoat and primer coverage question

Sorry. I didn't know how to title this but here is the deal.

I basecoated my 69 Firebird completely and cleared the jams. Then I assembled it with doors and fenders. While doing that I had a stand tip over and scratched my fender. Thank God it did not dent. Anyway, while I was wet sanding with 600 I found a few other spots I could fix.

So here I am with white sealer, then yellow base, and about ten gray patches on various panels including the hood. After wet sanding there are a few white shade spots as well.

So should I spray white epoxy as a sealer over the gray high build patches or just spray yellow base to cover? My gut says you will see these spots if I don't go white. I don't want to spray the whole panel white but I guess I should also get your opinion on that.

Thanks,

SAM

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:08 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.