Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> rebuilding my first holley 3310
User Name
Password
lost password?   |   register now

Thread: rebuilding my first holley 3310 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-03-2012 02:04 PM
engineczar That carb stock had 72's on the primary side and 76's on the secondaries. An 85 power valve, .025 squirter, and a plain colored spring on the secondary diaphragm.

Personally I get all kinds of carbs in the shop that the owner say runs like crap. Most times putting it back to stock straightens them out. Unless it's had the air bleeds and/or the metering blocks messed with I find that stock to maybe 1 or 2 jets higher gets you pretty close.
10-03-2012 01:08 PM
vinniekq2 If the bib block hat a hot cam then the power valve should be closer to stock for your application.note jet sizes and go up or down 2 sizes at a time.If you are lucky then the carb may have been modified to have change able air bleeds,note their sizes too if they are remove able. a standard 30 ss pump is all you will likely need and the cam position is adjustable so I wouldnt change it yet. check pump discharge nozzle size while the carb is apart
10-03-2012 12:56 PM
E.Furgal the rebuild kit is a holley master kit..
it was 99.oo at summit.. it has a few powervalves/etc

this carb was on a very hot bbc in the 80's so , this is why I'm asking where to start with the jets/ect as I'm sure as it it be eye watering pig rich..
but haven't opened the carb up to know what # jets/power valve is in it.
10-03-2012 12:49 PM
vinniekq2 I would use the jets that are in it.Take note of the numbers. If you do a jet change go up or down 2 sizes,not one.Use holley power valves some jobber kits have PVs that are not very good.
10-03-2012 12:10 PM
E.Furgal
rebuilding my first holley 3310

Hello, I'll be rebuilding my holley 3310 (750 vac 2nd) carb. that I got from a friend.. it was in runnable shape when I got it.. clean and in a holley carb travel case..
I have the complete tear down rebuild kit. figured do it once all the way down..
this part shouldn't be all that hard.. other than installing the choke kit

my question is tuning.. as I'm sure the jets/ramps/etc was changed as it was on a not stock ,engine.. before I got it..

it's going on my 71 c-10 350 with a edle performer intake under it.
the 350 nothing special.. and no idea what it is.. other than a 350.
figuring it's either the 71 engine or a mid 70's early 80's smogger.. thats stock..

where would you start with jet sizes, ramps/cams(or is that just double pumpers?)
the bowls don't look stock.. and this carb has metering blocks on both sides not a metering plate on 2nd side..
thanks for any pointers to get it somewhat close as I rebuild it..

not sure if it's needed.. but the truck is 3950 lb with 3.08 gears 26.5"tires(tall)

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:10 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.