Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> sbc first start up
User Name
lost password?   |   register now

Thread: sbc first start up Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-04-2012 10:03 AM
SBC first start up

I would prime the oil system again before start up. Here is some info to read about installing a distributor.
10-04-2012 09:46 AM
JOHNSHENOUDA I had the caps off for about a week or so. Still have not made final hook ups to the dryer and such. I think it would be best to remove, empty and refill. Will there be any issue with PAG 100. i was told to use PAG 120, what is the difference?
10-04-2012 09:35 AM
vinniekq2 How long was the A/C system left open? was it sealed during repairs?Disconnect the power to the compressor.There is no way of measuring oil still in the system that I am aware of. receiver/drier may need to be replaced.when you take the car for evacuation and recharge explain what happened.
10-04-2012 07:29 AM
sbc first start up

So I have this newly rebuilt sbc350. Getting ready to fire for the first time. Added the fluids last night. Kind of had a bear of a time getting the distributor to drop in and have it point at cylinder #1. Finally got it! I cant seem to tell if it is at TDC or not. No way I can get a wrench on the cam to turn by hand. Simply not enough room. Heck I can't even see the harmonic balancer to get an idea of were the mark is. If I take off the first spark plug and have someone turn the key with my finger over the hole will I be able to get the piston to TDC in cylinder one? Is there an easier way? Will I have to take that darn distributor off again after finding TDC? I did prime the pump before dropping the distributor down. Should I do it again today before firing? Lastly during the process of assembly the oil in the air conditioning compressor spilled out on the floor. I was told by Vintage Air that I should use PAG 120 and put in 7.2 ounces. I was only able to find PAG 100, how will I know that I have 7.2 ounces in it. Do I have to take off the compressor and dump out the oil and then refill? What a pain.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:26 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.