Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Want more power out of 427
User Name
lost password?   |   register now

Thread: Want more power out of 427 Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-07-2012 06:15 PM
kwillymac You could make that kind of power with a 427 and a 177 weiand supercharger. The pistons are a problem. I have a 454 with a 174 B&m Blower that made 670 hp and 646 ftlbs torque. Solid cam, rectangular port heads cast iron, 8.25:1 compression.
10-06-2012 09:00 PM
Originally Posted by F-BIRD'88 View Post
....but I would get a Weiand 8-71 and two 750 edelbrocks for it on this motor. (+ the solid or solid roller blower cam)
That would be my choice, my 383 is an 8-71 motor, two Demon 750BC's, solid roller and very streetable.
10-06-2012 05:38 PM
67-4-fun I would swap out the camshaft for something like this one from Lunati Street Strip Hyd Cam - Chevrolet Big Block 285/295 - Lunati Power then buy you a 100-150 shot cheater nitrous system, good street motor then nos if you go to the strip.. 100-150 is pretty mild shot for bbc.. this setup may cost you less than $500-$600 you get the power you want and have fun for lot less than a 2 grand blower adder not blower wouldnt be cool, but i think you dont have the right SCR or the right setup for it, NOS just bolt on and go once you learn a few detail before you run it, not hard, just common sense
10-06-2012 01:55 PM
Originally Posted by View Post
Most 427 BBC high compression pistons can't be cut to flat top safely.
I agree. I'm no engineer, but from what I've been able to put together over the years, good engineering practice dictates that the crown thickness will equal about 7% of the diameter for a naturally-aspirated piston. The crowns on dedicated blower pistons will be thicker than those on naturally-aspirated pistons, so you would want to be adding material, not cutting material away. I don't know what the percentage of crown thickness to diameter would be with a dedicated blower piston, but common sense tells me 8% to 9%.
10-06-2012 01:35 PM
68NovaSS Doesn't seem reasonable to expect 650 out of a little 177 and 427 c.i., that's JMO>...
10-06-2012 01:26 PM
vinniekq2 my87z is correct
what I said,heads = 60 plus hp.50 cubes will add 60 plus hp,torque would go up.

or like I said 60hp for better heads and maybe 20 more with a roller cam,thats 600,,,
blower or 496 will both need new pistons.
do the math on the cost of parts and see what works best for the situation? a 496 can use bigger heads than a 427 so more power potential there
10-06-2012 01:07 PM
my87Z ^^^^^X2

the reason most people are saying that going the blower route will be expensive is for 1 the blower is going to cost 2500+ to get it delivered. Then I would say that it would be a little dumb to run a blower on facotry heads (just my opinion) and I'm not sure those heads in the shape they are in can even support 650hp. So there is a set of aftermarket heads, 1800-2500. To do this he is looking at 5,000 easy, and that doesn't include the machine work to the pistons (i'd just buy new pistons).

Since this is a 427 BBC which is basically the same block as the 454 BBC just with a 396 crank, I would say go after building a 496, he'll have about 2500 into the rotating assy and the machine work. Then go after the aftermarket heads, and probably another cam. It isn't too hard to make 600-650hp out of a 496 (with the tq to match). Then later on if he decides he wants even more then he could toss a blower on it and be in the 750hp range (suposing the block and other parts hold up).
10-06-2012 12:34 PM
apexrig1 He is just looking for a way to get around 650hp or so and we figured this would work fairly good.

Can a person get that high with just changing to better heads and upgrading to a hydraulic roller? It's currently a solid flat tappet
right now.
10-06-2012 12:26 PM
vinniekq2 who wants the blower,you or the owner? a better set of heads will add 60 plus hp
10-06-2012 12:22 PM
apexrig1 He has the 781 oval port heads. They have been ported with 2.19/1.88 valves.

I can't see it being very expensive to do that's all. Because all he needs is to lower the compression change cam and stick the little weaind 177 on there? Or am I missing something?

Is there a way to tell if the done is hollow or not??
10-05-2012 08:12 AM
AutoGear When you say strict budget, what do you mean? To me, "blower" and "strict budget" don't go together
10-05-2012 05:11 AM Most 427 BBC high compression pistons can't be cut to flat top safely.
10-04-2012 11:35 PM
SSedan64 If the Domes are solid they can probably be milled down enough. If they're hollow Domes no go.
10-04-2012 10:11 PM
vinniekq2 Depends on what is already in the engine. What heads are on the engine at this time? 650 HP is easy with a blower/turbo and 575 is very street able in normally aspirated.
10-04-2012 07:06 PM
Want more power out of 427

Hey everybody I have a few questions in hoping you can help me with. A friend of mine currently has 427 bbc that ran 520hp on the dyno. Now after a few years he wants more power closer to 650hp. No nitrous. He is on a very strict budget. Now the motor has forged crank and forged domed pistons. Now I thought in my mind he could disassemble the motor have the pistons milled down to be flat tops giving it around 8.5:1. Put a weiand 177 blower ontop. Possible upgrade to a hydraulic roller.

Would this work? If not could I get input on what you guys would recommend? This is strictly a street motor in a 71 gmc half ton.

Thanks a bunch

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 04:56 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.