Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Schaefer Aluminum Flywheel ??
User Name
lost password?   |   register now

Thread: Schaefer Aluminum Flywheel ?? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-05-2012 05:29 PM
lmsport For light weight and street use I would recommend steel. The old LS7 flywheel and the neutral balance flywheel for the 84-85 F-body weigh about 15 lbs. Both are available new from GM for about $200. I have raced these two in oval track cars for thousands of laps without an issue. For even lighter weight, I would go to a 7.25" or 5.5" clutch setup along with either a flexplate or special starter and 104 tooth flywheel.
10-05-2012 04:30 PM
Nailhead2x4 ....Thanks BOBCRMAN for the info , I'll pass this on to the potential buyer. Looking at the surface I can't see any coating, must be pretty invisable stuff and it don't look like it was ever refaced. I'm still amazed they made something like this.
10-05-2012 04:26 PM
Originally Posted by vinniekq2 View Post
you can buy light weight steel flywheels,dont use the aluminum. I bought a medium light weight steel flywheel,its 26 pounds
.......This one weighs 11 3/4 lbs , thanks for suggestion.
10-04-2012 06:38 AM Flywheel surface cannot be economically repaired/replaced. A one time only situation.

High heat/horsepower will destroy the surface. Then you get de-laminating, galling and smearing of the surface. Once the disc slips, the surface goes away fast! Been there.

Organic clutch materials only. Ceramic and/or metallic discs create less heat but will abrade the surface thru the coating.. Don't ask how I know...
10-03-2012 10:30 PM
vinniekq2 you can buy light weight steel flywheels,dont use the aluminum. I bought a medium light weight steel flywheel,its 26 pounds
10-03-2012 09:30 PM
Nailhead2x4 ......Thanks 4 the replies guys. Well I learned something, didnt know that this type of flywheel can not be refaced. Sounds like it should be just hung up in a museum. The machineing marks are still visable and some blemishes on the face no real groves, so I think it can still be used ok, BUT for how long if really put alot of horsepower to it ? Does anyone know if the laminate can be redone ? And if worn off will she start slipping big time or what will happen ? What type of clutch works best with this flywheel ? Thanks.
10-03-2012 07:40 AM
AutoGear My God I haven't heard or seen one of these since 1988, and it was old back then. Cool stuff. As Bob said, you can't resurface it, and if its used, you'll want to check it very carefully before you use it. Additionally, since it can't be resurfaced, you'll also want to think about how much you plan on using your car.

Keep us posted.

PS My dad had one with a Zoom clutch back in 1968 and loved it. Put his car back together in the early 2000's and looked at a new Zoom clutch - less than impressed.
10-03-2012 05:07 AM The car will have to be set up correctly to use an aluminum flywheel. Most drag cars rely on a heavy wheel to get a good start.

Good for a big engine car with small tires. Or a high horse street car on regular tires.. Poor initial traction situations.

Schaefer wheels don't have an insert clutch surface as most others did. NO resurfacing of these wheels as the bonded friction coating is just a few thousandths thick. Friction surface had problems de-laminating under big torque/heat situations. Choose clutch disc carefully.

On another site, I detailed the problems that are to be expected with these aluminum wheel use. These wheels and the bonded aluminum pressure plates were big warranty headaches. Back in the day.
10-02-2012 09:20 PM
Schaefer Aluminum Flywheel ??

This is a vintage Schaefer aluminum flywheel, small block chev internally ballanced , 168 tooth , diameter less ring gear is 13 7/16" , center hole is 2.48" . It has markings on it Schaefer , Alcoa , 6PA-2 and 30 22008 .
Question : will this work safely on a 600 hp sbc ? I bought it used many years ago but never used it and a guy wants to buy it from me . I have no experience with them as too how much hp they can take . I believe Schaefer was good stuff back then ?? any info appreciated, Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 02:17 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.