Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Sealing a poly tank?
User Name
Password
lost password?   |   register now

Thread: Sealing a poly tank? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-07-2012 02:18 PM
Jim Rockford Pick up a plastic welder kit ... They work great .

Plastic Welder & Welding Kit

http://www.ebay.com/itm/80-Watt-Iron...item4aaf0b191c
10-07-2012 02:16 PM
ForceFed86
Quote:
Originally Posted by boatbob2 View Post
Hi,remove the fittings,then using 40 grit sandpaper,rough up that area,very good,(about a 3 inch square) then using EPOXY and 10 ounce cloth,put about 3 to 4 layers of cloth on,( I would use 10 ounce boat cloth)(fiberglass cloth) where the holes are ,in the 3 inch square,,then using a spatula (metal or plastic,) remove excess epoxy from cloth. leave it for 24 hours,in a warm place,you will be good to go.
Do you know if most epoxy/resins are compatible with ethanol? Any specific ones that you know 100% are? I've had problems in the past with certain epoxies etc....

thanks!
10-07-2012 10:56 AM
boatbob2
Removing fittings...

Hi,remove the fittings,then using 40 grit sandpaper,rough up that area,very good,(about a 3 inch square) then using EPOXY and 10 ounce cloth,put about 3 to 4 layers of cloth on,( I would use 10 ounce boat cloth)(fiberglass cloth) where the holes are ,in the 3 inch square,,then using a spatula (metal or plastic,) remove excess epoxy from cloth. leave it for 24 hours,in a warm place,you will be good to go.
10-06-2012 06:09 PM
ForceFed86
Sealing a poly tank?

I'd like to seal some ports on the sump of this cell. Because my car is a hatch I've built a steel box to place the tank in. I'd like to seal the holes of the old fittings and relocate them to the bottom of the sump. (marked with yellow grease pencil).

The surface of the tank is so oily and slick I was wondering what I could use to seal the original holes it? I'll be running e85 so it has to be compatible. I know JB weld is not ethanol compatible from past experience. I suppose I could just cap the two fittings and run another one. I'd like to reuse/relocate the fittings if possible though.

Thanks


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:42 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.