Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> HEI distributor problem.
User Name
Password
lost password?   |   register now

Thread: HEI distributor problem. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-10-2012 11:37 AM
SSedan64 Wow! What a pain in the buttocks.
Pertronix should have better QC than that. Very sloppy.
Glad you found the problem.
10-09-2012 04:52 AM
staleg Problem seems to be solved.
The ignition module wasn't fastened. It was just laying loose and held in place by the wires and the fact that there isn't much space around it.
The two missing screws are also grounding the module.

This is how the module was out from the box.
Will contact Pertronix support an ask if the can send new screws.
09-28-2012 12:10 AM
staleg I have tried with additional ground.

A friend of mine tested the first coil according to instructions found on this page. The test indicated a bad coil. That's why I have changed it.

Didn't test the new one before mounting. Guess I have to do that as well, but how likely is it that two brand new coils are both bad?
(Yes I know I know... The master cylinder I have is the third one. The two first ones were leaking past the piston...)
09-27-2012 03:16 PM
cobalt327
Quote:
Originally Posted by staleg View Post
1934 Ford Roadster Hot rod, first start attempt. 350 Chevy engine.

-Car turns over but won't start.
-Brand new Pertronic D1000 coil in cap distributor.
-All new electric wiring in the car. Made for electric ignition.
-Distributor get 12V power when cranking and when the key is in "on" position.
-Have changed the coil once. Didn't help.
-No spark.
-Have tried a different set of plug wires. No help.
-Have tried to turn the wires 180 degrees on the distributor - no help.
-Brand new spark plugs.
-Fuel is ok as plugs are getting wet after cranking.
-The cranking itself sounds normal.

Any ideas?
Distributor grounded to the engine? If it has a gasket under it, the clamp and bolt into the block becomes the ground pathway- can't have paint insulating it, etc. You can't really rely on the distributor/cam gear to be a sufficient ground.

The coil can be tested using an ohm meter. If it's OK and w/the rest of the things you've listed all good, as long as it's grounded that leaves the module as the most likely culprit.

You didn't leave the rotor off, right?
09-27-2012 03:06 PM
70Caprician And everything's well-grounded? That turned out to be the reason my MSD 6AL box wasn't firing (after I had tried everything else as you've apparently done)...
09-27-2012 02:22 PM
staleg
HEI distributor problem.

1934 Ford Roadster Hot rod, first start attempt. 350 Chevy engine.

-Car turns over but won't start.
-Brand new Pertronic D1000 coil in cap distributor.
-All new electric wiring in the car. Made for electric ignition.
-Distributor get 12V power when cranking and when the key is in "on" position.
-Have changed the coil once. Didn't help.
-No spark.
-Have tried a different set of plug wires. No help.
-Have tried to turn the wires 180 degrees on the distributor - no help.
-Brand new spark plugs.
-Fuel is ok as plugs are getting wet after cranking.
-The cranking itself sounds normal.

Any ideas?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.