Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> roller cam retrofit kits, best quality-lasting
User Name
Password
lost password?   |   register now

Thread: roller cam retrofit kits, best quality-lasting Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-11-2012 03:30 PM
cdminter59
roller cam retrofit kits, best quality-lasting

Crower .641/.636/ and 256/266 with 107 LSA and 103 C/L. Great camshaft with no problems, had in my 454 since 1998.
10-10-2012 10:13 PM
vinniekq2 I have a comp cams camshaft and I was told to try crower rollers.I have crower rollers in my engine now.so far no problems,7 years old now.When I freshen the engine I will replace the rollers.Ive replaced the springs once already.
10-10-2012 07:26 PM
oldbogie
Quote:
Originally Posted by E.Furgal View Post
Hello..
I have a 355 small block chevy that I built way back in 1991-2 .
it was built with the good stuff.(well as good as a kid with a low wage job could). lunati crank , oliver rods,
trw floating pin pistons, comp 292 cam and roads lifters, brodix trackI heads,
bowtie single plane intake, arp everywhere..
then life hit,, fast forward to 2012-13 it's still never been ran..
I know I have to open it up as the moly lube is mostlikely mud..
and was thinking of changing to a roller cam and maybe a rev kit(if they are still used/needed)
like to stay hyd if I can get a cam that work with the intake/heads compo.. as I've heard horror stories about the solids lifter failing on a street driven car..
help, thanks...
and before someone says it.. yes I could use it as it, with the 292 cam.. but with todays oils and flat tappet cams failure rate.. I'm thinking I'll pass..
but feel free to make points to try to talk me out of a roller.. I'm all ears..
I have used a thrust button for many years with flat tappet cams in Chevy's, this unloads the lifter and lobe from the job of stopping thrust excersions. My FT failure rate is mostly nill. Not that I'm against roller cams mind you. Plus they can fail as well sometimes the roller just skates the end result looks a lot like a flat tappet out to lunch so you have to be dilligent with these as well.

Bogie
10-10-2012 04:04 PM
techinspector1
Quote:
Originally Posted by E.Furgal View Post
Hello..
I have a 355 small block chevy that I built way back in 1991-2 .
it was built with the good stuff.(well as good as a kid with a low wage job could). lunati crank , oliver rods,
trw floating pin pistons, comp 292 cam and roads lifters, brodix trackI heads,
bowtie single plane intake, arp everywhere..
then life hit,, fast forward to 2012-13 it's still never been ran..
I know I have to open it up as the moly lube is mostlikely mud..
and was thinking of changing to a roller cam and maybe a rev kit(if they are still used/needed)
like to stay hyd if I can get a cam that work with the intake/heads compo.. as I've heard horror stories about the solids lifter failing on a street driven car..
help, thanks...
and before someone says it.. yes I could use it as it, with the 292 cam.. but with todays oils and flat tappet cams failure rate.. I'm thinking I'll pass..
but feel free to make points to try to talk me out of a roller.. I'm all ears..
I would never try to talk you out of a roller, I think it's the only system that makes any sense today. Current hydraulic roller technology puts the rev limit somewhere around 6200 because of the weight of the lifter and oil in it, so if you are planning to make power below 6200 (most street motors), a hydraulic roller makes sense. You can rev higher than that with a rev kit, but for my money, if I wanted to rev higher, I'd begin with a solid roller cam.

Progress rolls on, so I would think that the manufacturers have the solid roller problem overcome by now, although I personally have not built a motor for the past few years. I'm retired now and have sold off all my equipment except for hand tools, so I try to limit my involvement to helping others on these boards to make sense of the basics.
10-10-2012 03:29 PM
E.Furgal
roller cam retrofit kits, best quality-lasting

Hello..
I have a 355 small block chevy that I built way back in 1991-2 .
it was built with the good stuff.(well as good as a kid with a low wage job could). lunati crank , oliver rods,
trw floating pin pistons, comp 292 cam and roads lifters, brodix trackI heads,
bowtie single plane intake, arp everywhere..
then life hit,, fast forward to 2012-13 it's still never been ran..
I know I have to open it up as the moly lube is mostlikely mud..
and was thinking of changing to a roller cam and maybe a rev kit(if they are still used/needed)
like to stay hyd if I can get a cam that work with the intake/heads compo.. as I've heard horror stories about the solids lifter failing on a street driven car..
help, thanks...
and before someone says it.. yes I could use it as it, with the 292 cam.. but with todays oils and flat tappet cams failure rate.. I'm thinking I'll pass..
but feel free to make points to try to talk me out of a roller.. I'm all ears..

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:37 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.