|12-27-2012 06:06 PM|
mostly snap on ,mac,some older craftsman tools i bought 50+ years ago a few sk with some cheaper tools bought over the years.i have a really good snap on dealer that stops at shop every monday.a pretty good mac man that stops when hes in the area or when i call him.no problem getting tools repaired or replaced. neet picture of older snap on dealer and tool truck
|12-27-2012 07:00 AM|
I have SK tools. I'm just a home machanic but I am in the garage every day, working on something. If I had to recommend a tool for someone it would be SK. My screw divers and sockets are about 18 years old and look like new, even being used by my wife when I'm not looking. One good point is they are US made. Good luck.By the way, all wrenches are SK also.
|12-26-2012 09:51 AM|
I bought one of these 3/8" palm ratchets off the Snap-On truck back in the late 70's or early 80's. It was just the right "tool for the job" ... which was header bolts and/or spark plugs on my 351C in a '68 Torino, if I recall. That engine was fairly "shoe-horned" in there.
I also recall heating and flattening out the 7/16" end of a box-end wrench in order to get to ONE header bolt snugged up. It was *just* the right length that you could get some good torque on it, but short enough to clear the shock tower and get some decent "swing room".
I still have both of these tools, and have found various other uses for them throughout the years.
|12-25-2012 12:21 PM|
My dad was a Snap-On dealer in the early 50's.
|12-25-2012 12:15 PM|
|12-25-2012 12:14 PM|
Absolutely guys, the mid grade tools are plenty good enough for most anyone. Gear wrenches for example, they work about 90% of the time for me and the SnapOns stay there for when I really need to muscle it on a suspension component or something.
I do have to say that a good tool in your hand makes the work much easier though. It' like the first time I held an American Made vintage Fender Stratocaster, holy crap what a difference from the guitars I had played before. It made playing WAY easier.
My Martin Hammers are so much better than the cheapo's I have it isn't funny.
|12-25-2012 12:10 PM|
BTW...The new one he gave me only lasted a few years......Since I no longer work and dont see the truck, I havent bothered seeking a replacement
|12-25-2012 12:01 PM|
|tech69||yeah, I say that now but when I got my craftsman 1/4" ratchet crammed in a tight area and the gearing just doesn't grab quick enought then i have a problem. THAT is when I dream of that Snap on 1/4" ratchet. On the most part my craftsman does fine.|
|12-25-2012 11:49 AM|
I must agree with Tech69 here....In the most part, its the guy using the tools that matters, within reason.......You can use a cheapo wrench just as well as a Snap-on, but when the nut/bolt is all rusty and the wrench is slipping off, that's when the good tools make a difference. My dad left me all his old tools...The Snap-on stuff is well over 50 years old now and still working.
What does bug me about some mechanics is when they have a carpenters claw hammer in their toolbox.......I know it works just as well, but have some pride man.....This is not meant to offend carpenters.....
|12-25-2012 10:54 AM|
|tech69||I'd like to state there's general tools that should not be cheap but for the most part the tech is the main tool. Materials are different. I like all high quality materials but as for tools, I've gotten over the fact that the best tools give you the best work. I will say that the RIGHT tool for the right job is more important than brand, but obviously since I do it everyday I'd rather have better tools but it's not what makes the work good.|
|12-25-2012 10:46 AM|
I haven't read every word of this thread but wanted to throw out there that the most important part to using any tool is that it is the correct tool as in the correct size as well. I have seen so many phillips screws and drivers destroyed because the guy was trying to remove a screw that required a larger or smaller screw driver.
You need to clean out the screw of junk, you need to slip the driver into the hole and wiggle it a little making sure it is the right size that it is filling the hole in the screw properly.
|12-25-2012 09:20 AM|
Used to be SnapOn. Since I don't work in a shop anymore, I don't buy a lot of new tools. I got tired of the Snap On men frowning when I ask to fix a broken Snap On tool. So now mostly Craftsman with the Snap On. As the Snap On break I replace them with Craftsman. Lots easier to get warranty and they work just fine for my home shop.
|12-25-2012 07:23 AM|
I am using mostly Snap on tools. What I have is the ones I used when I worked as a Heavy Equipment mechanic. I just moved them from my service truck to my shop.
|10-12-2012 02:53 PM|
|10-12-2012 02:51 PM|
Ive been using hand-me-down handtools for years. S*K has been my favorite; no idea on their quality now that they're owned by Cooper Industries. My dads SK ratchet finally gave up the ghost; I called up a local shop that repped SK and he wanted 25 bucks to sell me the guts for a ratchet, that MIGHT work in my dads old (1970 vintage) ratchet. Screw it; I went to Sears and bought dad a new one. That thing is SUCH a pile with the coarse teeth, and they get so much junk in them they barely cycle after awhile (you can flush them out with PB Blaster, if you remove the snapring too many times it will deform). UGH!
My screwdrivers are Klein, I also have some old Proto (?) I like as well
|This thread has more than 15 replies. Click here to review the whole thread.|