Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 1989 SBC Using Oil
User Name
Password
lost password?   |   register now

Thread: 1989 SBC Using Oil Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-26-2012 01:39 AM
jayd_2 The intake gaskets were leaking oil on all cylinders, replaced the Felpro with some soft gaskets. Oil consumption problem solved and it runs much better.
10-18-2012 11:30 PM
Plaintoast the head gaskets are standard, the intake gaskets from fel pro will had just a small bleed hole in the rear water jacket crossover, but a standard one will work. the valve covers are different and not interchangeable
10-18-2012 09:07 PM
jayd_2
Quote:
Originally Posted by Plaintoast View Post
normally those are referred to as throttle body heads.
good chance they are either 191 or 193 castings, assuming 350 and not 305.
Do these heads require different gaskets than previous sbc heads
10-18-2012 08:28 PM
hcompton
Quote:
Originally Posted by jayd_2 View Post
What will cause a good running engine to burn lots of oil?
Borken ring land, rings upside down, valve seals, some strange restriction in the oil system causing oil not to leave the head fast enough and flooding the heads, scratched or out of round bores, missing rings and so on...

Gaskets are always the first suspect.

Pretty much as long as its fresh and has good strong compression it will burn up a ton of oil. Wouldnt be suprised if its still strong on 7.

they make oil fouler devices its like a tube that moves the spark plug back. It can stop it from craping out the plug every few hundred miles. But not a fix for sure. even if its just a gasket you dont want the carbon build up.

A leak down and compression test will shed some light on the problem.
10-18-2012 08:08 PM
jayd_2
Quote:
Originally Posted by hcompton View Post
I use print-O-seal gaskets for alum intakes. seem to work fine.

first thing in the morning with the engine cold. get someone to hold a white sheet of paper behind the exhuast and start the car and rev it up a few times.

Let it dry there should be water. then look to see if there is any oil on the paper. If so its burning oil for sure. Also check for black dust on the back of the car and bumper around the exhuast. check both pipe if you have dauls so you can compare.

A good running engine will burn a lot of oil without showing many signs. Its usally the old engine that shows the oil burning with thick white smoke.

I would do a leak down and compression test before taking anything apart. no reason to pull the intake and replace the gasket if you have a broken ring land. A broken oil ring land will still run ok in a v8 but will burn oil like mad.


Hope this helps
What will cause a good running engine to burn lots of oil?
10-18-2012 06:40 PM
Plaintoast normally those are referred to as throttle body heads.
good chance they are either 191 or 193 castings, assuming 350 and not 305.
10-18-2012 06:32 PM
jayd_2 The 2 center intake bolts are at a different angle than the outside bolts, what type heads are these?
10-18-2012 02:47 PM
hcompton I use print-O-seal gaskets for alum intakes. seem to work fine.

first thing in the morning with the engine cold. get someone to hold a white sheet of paper behind the exhuast and start the car and rev it up a few times.

Let it dry there should be water. then look to see if there is any oil on the paper. If so its burning oil for sure. Also check for black dust on the back of the car and bumper around the exhuast. check both pipe if you have dauls so you can compare.

A good running engine will burn a lot of oil without showing many signs. Its usally the old engine that shows the oil burning with thick white smoke.

I would do a leak down and compression test before taking anything apart. no reason to pull the intake and replace the gasket if you have a broken ring land. A broken oil ring land will still run ok in a v8 but will burn oil like mad.

Hope this helps
10-18-2012 01:07 PM
oldbogie
Quote:
Originally Posted by jayd_2 View Post
I've got a 1989 SBC that was a rebuild that had about 5000 miles on it when I got it. It runs great but uses oil and fouls the number 8 plug but does not smoke. The plug fouls after several hundred miles, all the other plugs are good. I just replaced the valve stem seals on number 8 but I doubt that was the problem. It uses half a quart in about 300 miles. The oil pressure is 30 lbs at idle and 60 lbs at rpm.

It doesn't smoke when cold or when under a load or when you let off at high rpm. How it could use so much oil without smoking? There are no oil leaks and the crank case pressure is good, pcv valve is dry.

Is it possible that the intake is leaking on one cylinder, it's got an aluminum intake and I've heard some gaskets are too hard and don't seal well on aluminum.
It could be a leak from the intake into number 8 but before pulling the intake off remove the rocker cover on number eight's side roll the engine over and observe the rocker movement to see if a cam lobe is wiped out.

Also, a vacuum check before diving in, a leak into the manifold should show a low but steady needle on idle that corrects as the RPMs come up. A wiped lobe will show a normal needle that dips everytime that cylinder comes around and stays that way as the RPMs are moderately raised.

Bogie
10-18-2012 10:14 AM
jayd_2
1989 SBC Using Oil

I've got a 1989 SBC that was a rebuild that had about 5000 miles on it when I got it. It runs great but uses oil and fouls the number 8 plug but does not smoke. The plug fouls after several hundred miles, all the other plugs are good. I just replaced the valve stem seals on number 8 but I doubt that was the problem. It uses half a quart in about 300 miles. The oil pressure is 30 lbs at idle and 60 lbs at rpm.

It doesn't smoke when cold or when under a load or when you let off at high rpm. How it could use so much oil without smoking? There are no oil leaks and the crank case pressure is good, pcv valve is dry.

Is it possible that the intake is leaking on one cylinder, it's got an aluminum intake and I've heard some gaskets are too hard and don't seal well on aluminum.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:48 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.