Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> My T-400 Tranmission Will not go into any gear.
User Name
Password
lost password?   |   register now

Thread: My T-400 Tranmission Will not go into any gear. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-24-2012 08:49 PM
Mrboykin0
Well I feel retarded

Thanks guys so helpful!

I checked the fluid levels again, but i didnt account for the fluid in the intercooler + fluid in the torque converter not to mention I have an After market B&M (deep) pan. SO there was my problem of why it wasnt moving/ going into gear.

So After adding more fluid, shes driving. And i was VERY excited! haha

But now it feels like there is a big power loss, like im having to rev too much to go a certain speed. fastest ive gone is about 20 mph.
I have a Bored .40 over 350, she should be puttin out 400+ Hp

Didnt get on it, because the last time i gave it a hard throttle The Vbelt FLEW off! It wasnt a big deal since the car was in Neutral and i was setting up the throttle link cable, but i wouldnt want that to happen while im driving!
10-24-2012 07:49 PM
WriterDennis I would say to check and recheck the tranny fluid level. Basically, the tranny works based on fluid pressure, so if the fluid is low, you ain't gonna go.

Dennis W. Parks
author of automotive how-to books
10-24-2012 07:28 PM
idontdrivericeieatit And I have never seen a torque converter spin without the flexplate or flywheel bolted to it. if its doing it separate thats a new one for me and would love to know how thats possible
10-24-2012 07:23 PM
idontdrivericeieatit Pull a transmission line and start engine put into gear and see if it sprays fluid out if it if it dont then its front pump if it does could be torque converter is bad but I would start with front pump as u dont have to pull it to check it and u sure has plenty of fluid mine dry took 12 quarts with the transmission cooler
10-21-2012 04:48 PM
RWENUTS DRain it time!
Check the filter again.
10-21-2012 04:25 PM
Mrboykin0 No they spin as one unit, Torq Conver is bolted to the flywheel

there is plenty of fluid in transmission
10-21-2012 04:03 PM
RWENUTS Did you put enough tranny fluid back in?
Flywheel spins! Torque convertor spins! Seperately or togethor?
10-21-2012 03:30 PM
Mrboykin0
My T-400 Tranmission Will not go into any gear.

I recently dropped a SBC (350) into my 1980 camaro, the transmission had been sitting out of the car for about 8 months, But when i drove it last, it shifted fine, so why it would stop working out of the blue is beyond me.
I did remove the oil pan and change the gasket/filter, but I thought I was very careful not to touch anything else.

The car is on jack stands
The only thing that works is park. At first I thought it was the shift linkage But then when i ran the engine, and moved the lever on the trans manually into the gears, NOTHING happens.

Reverse or 1st,2nd,3rd. Nothing
Driveshaft is seated correctly
the fly wheel spins, the torque converter spins.
When I installed the torque converter I was very careful to make sure I got the "Two clunks" so to know it was seated properly

The vacuum line from the (edelbrock) carb to the modulator is set up correctly, and there is plenty of FRESH automatic fluid in trans as well.

There is an electrical plug on the driver side But i dont ever recall it being set up even when it was driving?
Is there something Inside the transmissions Im suppose to connect?

This is making me crazy, Ive been working on this car forever Im so close to driving this car and the amount of frustration is becoming unbearable.
There are very few people I could ask for assistance.

Please lend some knowledge, Im 21 and have much to learn.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:24 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.