|11-09-2012 09:12 AM|
|Caballerokid||Again cant use a vortec head. The chambers are too small.|
|11-09-2012 09:11 AM|
|Caballerokid||Where could i maybe get a better deal on the Dart heads? Summing has taken very good care of me so far but ive never purchased heads before.|
|11-09-2012 09:10 AM|
I've built a couple of engines this year using these:
Vortec Hybrid Marine Cylinder Head with Heat Riser | eBay
Talk about cheap HP if you're trying to use an intake you already have. I was skeptical but the quality was excellent. Throw in some valves and springs from Competition Products and for under $600 you have yourself a nice top end.
In your case the chamber is also too small (64cc)
|11-09-2012 09:09 AM|
|Caballerokid||I can't use those heads. The chambers are too small... that's why i asked about 76cc iron heads and 72cc aluminum heads.|
|11-09-2012 07:27 AM|
For the money these heads can't be beat: Assault Racing Bare SBC Small Block Chevy Aluminum Cylinder Heads Straight Plug 350 383 400 - KMJ Performance
Buy them bare and assemble with some light valves and beehive springs and you'll have a very nice set of heads that are perfect for hot street applications.
|11-09-2012 12:04 AM|
|Caballerokid||So not to beat a dead horse here but i have been doing tons of research. Heres where i'm at... I picked up a set of 441 heads for dirt cheap (couldn't pass them up). Now is it worth the money to completely go through them, bigger valves, back cut the valves, mild port and polish work, ss swirl polished valves, valve job, guides done yada yada yada... or should I just pick these up? I'm easily going to spend that on these heads... so what do you guys think, where is my money best spent here? Thanks|
|11-02-2012 09:28 PM|
|11-02-2012 08:52 PM|
|vinniekq2||just buy an engine and bolt it in|
|11-02-2012 08:36 PM|
|Caballerokid||Thats great and all but thats not much cheaper than going the blower route. That route would be roughly $4000 all said and done. The blower route would be about $4,500 - maybe $5,000 plus with the blower I'd probably have the potential to make nearly 600hp??? If I would need to go big, why not go all the way? I'm just asking... for all the work I would do to replace all that and make that kind of power, why not throw the blower on it and make more hp for only $1000 more? Now if we're talking like $2000 or more difference I could see not going all out and maybe staying a little more conservative, but $1000 idk. I haven't made my mind up yet because it is still only a 2 bolt main motor. There is still a 3rd option on the table... throw this out all together and weld in an LS motor for that price with a decent turbo. Idk...|
|11-02-2012 08:20 PM|
More TQ than HP???
Let me show you what you could do with a set of out the box aluminum heads. About 180-185cc intake runners, 72cc chambers, 2.02 & 1.6 valves. A.015 steel shim head gasket. A solid roller camshaft 12-771-8 XR280R .570/.576 lift and 242/248 duration @ .050. Your short block and a Victor JR with a 750 Demon Carburetor. On the dyno from CamQuest this combo would make Peak HP 431@5500, Peak TQ 441@4500. Add 2.08 valves and pocket port the heads and gasket match heads and intake. The peak HP would be 512@6500, 470 TQ@5000. Your compression raio would be 10.571 and the DCR would be 8.613. I don't think the deck clearance will be no more than .025 when checked. So this engine will have a .040 quench. The DCR being a little high mix some 93 and 110 octane gas 4:1. You wouldn't have to worry about detonation and you could add timing if you need it.
|11-02-2012 08:08 PM|
2. The squish is 0.055", not that far off the preferred mark of 0.035" to 0.045".
3. He has 76cc heads now. Smaller chambers will raise both the static compression ratio and the dynamic compression ratio and will not change the squish. How do you see that as helping?
|11-02-2012 06:44 PM|
|Caballerokid||Are you saying .555" lift is too small for a blower? That would be the cam i would use instead of the one i already have. The one i already have would take me to 13.5:1 cr at 6lbs of boost. Also why would you not blow a motor but rather turbo one? Theyre both stupid expensive... If i were going blower route the whole motor would be different except the bottom end. Also 400hp isnt my end goal. I want to make at least 400hp. More is better but at least 400.|
|11-02-2012 05:56 PM|
|11-02-2012 05:53 PM|
|lmsport||A 360 inch engine with 3.5cc domes, a .055 deck, .015 gasket and 76cc heads is only about 9.4:1. I think the knock you are fighting is due to the excessive quench. Get some 70cc aluminum heads and you will have pump gas compression.|
|11-02-2012 05:46 PM|
|Caballerokid||I understand... i was asking about that specific setup. What could i potentially see from that? Also, what would be a good 76cc head/cam/intake to get me to 400hp? Thanks|
|This thread has more than 15 replies. Click here to review the whole thread.|