Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Carb spacers do work
User Name
Password
lost password?   |   register now

Thread: Carb spacers do work Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-16-2012 06:39 PM
Nemeth
Carb spacers

Well I got so many different answers that I went and bit the bullet and bought several sizes of 4 hole and opens.... Funny the guy at the speed shop told me an open spacer would kill my torque all around....wrong made the bottom a little softer but between 2600 to 6000 I gained a whole lot more seat of the pants pull made me much happier with my build!!!! Was starting to think 383 was a bad choice but know my mind is changing...

Well lets see wat an open hole 1.5 spacer dose.Also I think my dissy advance springs are to tight cause It advances kinda slow when throttle is snapped. Ill try a curve kit and hope nothins wrong with my HEI.

Got to read and experiment first.....before questions are asked and to many wrong answers are given!!!!
11-16-2012 04:56 PM
Richiehd I installed a 1 inch Super Sucker on my 350. World heads, 200 cc runners solid lifter cam. It really woke up the mid range from 3000 to 5500
11-16-2012 11:59 AM
techinspector1 Good on ya mate, for experimenting.

For you other gearheads out there......
Each motor combination is different, so there is no set of rules as to the configuration or height of spacer(s) to use. Try different spacers and combinations of spacers to find if they help your combination.
11-16-2012 11:29 AM
Nemeth
Carb spacers do work

Hello every one I had a 4 hole spacer atop my performer rpm air gap it really did not pull well.I have a sbc 383 rhs heads 180 cc runners 10.5 to 1 comp 236-242 @ ,050 .550 lift 110 lsa.670 worked avenger.
I installed a 1 inch open spacer....engine came to life and pulls hard mid range.
Seems an engine with after market heads and a decent size cam with a dual plane manifold do much better with open spacers.

How ever an engine with mild build like my 327 with vortec heads performer intake,600 eddy carb comp 218-224 @ .050 9 to1 comp run better with a 1 inch 4 hole spacer.Smaller builds need more velocity for the low end torque.

That is my conclusion after testing both engines with different spacers....

SO YES SPACERS USUALLY DO MAKE A BIG IMPACT ON ENGINE PERFORMANCE !!!!!!!!!!!!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:03 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.