Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Lower from Shock stud 1940 Ford Coupe
User Name
Password
lost password?   |   register now

Thread: Lower from Shock stud 1940 Ford Coupe Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-27-2012 06:30 PM
artistsport3 Thanks for the response........I will use a "hot" wrench cautiously.......Not only is the brake line close but the fuel line and filter is above.......tucked into the frame below the fuel pump on the 383.
11-24-2012 04:37 PM
streetrodderbn The "hot wrench"(torch) will bake the shock rubber bushings(probably set them ablaze) and you can remove the old shocks and you then can reuse the studs and bolts, just have a box of baking soda handy-or water to douse the flames- should it ignite, and keep the flame away from the brake lines-brake fluid is flammable! Then measure the old shocks, I will look on sunday, I think I have a replacement set from Pete and Jakes to steal a part number from for you.
11-23-2012 07:56 PM
cobalt327 Must be a conversion, at least I thought the originals weren't tube shocks. But in any event, they should come off by prying the shock eye from the stud, unless I'm missing something.
11-23-2012 04:30 PM
454 Rattler Could you post a picture or two ? It might help get some answers.


454 RATTLER
11-23-2012 10:40 AM
artistsport3
Lower from Shock stud 1940 Ford Coupe

Help! I'm not smart enough to figure this out. I am trying to replace the front TUBE STYLE shocks on my solid axle 40 Ford Coupe. It has "Allstate Supramatic tube shocks #8158 3LD". Since it has MADE IN AMERICA on the shock....I think these are elderly....Got the top bolt nut off as well as the lower. Tried to push the bolt (stud) through the casting but it was a NO GO. The lower stud has a flat round surface that holds the shock from the inside which bolts to a cast piece mount on top of the spindle.What I have from the outside in is: is a threaded stud...then the cast piece...then the shock....then the round flange.(nothing to grab on to) I didn't want to pound on it VERY Much........Any advice?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.