Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Shrunken SBC Exhaust Manifolds
User Name
Password
lost password?   |   register now

Thread: Shrunken SBC Exhaust Manifolds Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-07-2012 09:17 PM
painted jester
Quote:
Originally Posted by fasteddy_1947 View Post
Yes. I never figured that the manifolds could warp while on the engine. They weren't binding when I took them off. The engine had been seriously abused in the past, so the warped manifolds were just another indication of it. Considered trying bend the right one out to where could get a bolt started, but don't know where to try to correct it in relation to the center ports. Think probably between the center and forward ports, as rear and center flanges bolted up (a little tight, but didn't cross-thread), and with my luck.. . Anyway, a quick trip over to the U-pull auto parts store and warehouse corrected the problem and I found a bunch of other stuff I need. I just thought maybe someone would have a quick and easy (or magic) fix, but there I go trying to think all by myself again. Thank you all for the input, and on we go to the next puzzling development for a highschool dropout trying to reengineer a machine that took hundreds of college trained automotive engineers to design and build. : )
Use studs and washers and bronze or brass or stainless nuts


Jester
12-07-2012 09:12 PM
fasteddy_1947 Yes. I never figured that the manifolds could warp while on the engine. They weren't binding when I took them off. The engine had been seriously abused in the past, so the warped manifolds were just another indication of it. Considered trying bend the right one out to where could get a bolt started, but don't know where to try to correct it in relation to the center ports. Think probably between the center and forward ports, as rear and center flanges bolted up (a little tight, but didn't cross-thread), and with my luck.. . Anyway, a quick trip over to the U-pull auto parts store and warehouse corrected the problem and I found a bunch of other stuff I need. I just thought maybe someone would have a quick and easy (or magic) fix, but there I go trying to think all by myself again. Thank you all for the input, and on we go to the next puzzling development for a highschool dropout trying to reengineer a machine that took hundreds of college trained automotive engineers to design and build. : )
12-06-2012 12:29 AM
cobalt327
Quote:
Originally Posted by fasteddy_1947 View Post
Am thankful the cylinder heads aren't growing. : )
Haa!

I'd say to make one using a heavy turnbuckle, but it might cost as much as the whole tool!

Look the manifolds over carefully. It's not at all unusual for them to have hairline cracks. Finding replacements shouldn't be a problem unless they're, well, a problem!

OEM Chevy exh. manifolds


The spreader will work good on some manifolds:

Not as good on some:

And not at all on others:

Lisle p/n 13000:
Good luck.
12-05-2012 09:56 PM
hcompton Bet its cheaper to get a used manifold than to have them machined.

Also block hugger headers are very cheap these days. Jet hot cloat if you want them to last and not rust but then they wont be cheap any more.
12-05-2012 09:17 PM
fasteddy_1947 Thank you painted jester. That makes perfect sense. This engine obviously been overheated, probably more than once. Pulled the engine out of 94 P/U I got real cheap, and found the engine to be so bad, I couldn't even use the original block. So, new block, crankshaft kit, other stuff to convert from tbi to carburetor. Should have just bought a rebuild. Would have cost less. Am surprised the heads aren't broken (and maybe they are, and I just don't know it yet). Thanks again for the tip. Am thankful the cylinder heads aren't growing. : )
12-05-2012 08:44 PM
painted jester At my shop I had an exhaust manifold stretcher I think you can buy them still ! Your manifold didn't shrink it warped and its common! Usually the studs brake or come out very tight when removing the manifolds because they were warped while on the engine Before tear down, and it isn't noticed by people till its assembly time! You should have them machined flat too sometimes there is a twist with the warp that wont let them seal!

My tool is a "Lyle 31000" exhaust manifold spreader

Jester
12-05-2012 08:28 PM
fasteddy_1947
Shrunken SBC Exhaust Manifolds

This isn't the first time, so I know I'm not the only one to run into SBC 350 exhaust manifolds shrinking. Same manifolds, same heads, same sides, but the holes don't line up now. Engine has been out since early summer. Will they shrink more the longer I leave them off? Left side went on after it learned some new words, but right side doesn't even look like it will listen. Have tried my six-pound coaxing wrench, but it be cast iron so got the result I expected: zip. I don't think the gas wrench will help any, either. Cold when took em off, cold putting them back on, and again, cast iron. Maybe the heads grew, but that's scary. Think last time ran into this, had to use different manifolds, but that was long time ago and had plenty around to try to fit then and don't think even used manifolds off 350, might have come off 400. Does anyone know the cure ? Thank you.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:39 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.