Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> edelbrock tunnelram
User Name
Password
lost password?   |   register now

Thread: edelbrock tunnelram Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-06-2012 04:16 PM
techinspector1 You want to go fast?....sell that POS and bolt a blower on.
12-06-2012 01:58 PM
hcompton
Quote:
Originally Posted by ap72 View Post
I have an Edelbrock 1406 (600cfm) carb on a 2.3L 4 cylinder and it runs fine.... So you can throw your "too much carb" theory in the trash can. Its car from too much carb especially when the secondaries rely solely on air demand.
Edelbrock carbs are usally Carter four barrel carbs and not vacum secondary type carbs. all four plates open staggered with cable on my 1406 no electric choke carb. Most edelbrock carbs are the same i think they are rebranding some other types for vacum secondary thunder series carbs.

But tuning is problably the issue. What is it doing. Common problem with those carbs is the accelerator pump must be set to its max setting and them sometimes upgraded for them to wok well in quick off idle throttle movments. Are they both electric choke or manual choke or a mix of both. You may have just gotten them mixed up. manual choke carbs come tunned for performance and electric choke models are tunned for gas milage. you should have two manual choke carbs on the tunnel ram. Yes it will require some good warm up time and a good choke cable setup.

I am betting someone with 500 cfm edelbrocks will trade you straight up and not blink. that being said I would just get them dailed in. Edelbrock is pretty good for phone support if your handy with carbs. if not may need some tuning time with local guru. If they need to be replaced let edelbrock determine this can you may be able to work a good deal for some remanufactured 500 cfm models.
12-06-2012 12:07 PM
bondo
Quote:
Originally Posted by blazinlow View Post
I picked up a SBC tunnelram with dual edelbrock 600 carbs. The carbs are too much for this engine.. Is there a way to lower the cfm on these carbs. I know it can't be done with Holleys , but don't know anything about edelbrock
Ayuh,.... I'd sooner think it's to much Manifold for yer motor,....

Just what, Exactly, is the motor yer tryin' to run this manifold on,..??
12-06-2012 11:56 AM
vinniekq2 what engine are you working with? what other parts are in the engine? How did you determine the carbs are too big?
12-06-2012 09:35 AM
ap72 I have an Edelbrock 1406 (600cfm) carb on a 2.3L 4 cylinder and it runs fine.... So you can throw your "too much carb" theory in the trash can. Its car from too much carb especially when the secondaries rely solely on air demand.
12-06-2012 08:52 AM
blazinlow
edelbrock tunnelram

I picked up a SBC tunnelram with dual edelbrock 600 carbs. The carbs are too much for this engine.. Is there a way to lower the cfm on these carbs. I know it can't be done with Holleys , but don't know anything about edelbrock

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:14 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.