Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> gear oil in hub/bearing carrier?
User Name
Password
lost password?   |   register now

Thread: gear oil in hub/bearing carrier? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-07-2012 07:21 PM
LATECH Look around here
Welcome to guzzle's 4x4 Needle Bearing Maintenance Web Page

The needle bearing (torrington style bearing )article is pretty informative
12-07-2012 07:07 PM
LATECH It is a sealed hub/bearing assembly. Shooting grease in the ABS hole is a waste of time.
I am not very impressed with Most dealerships/dealer mechanics.
If you are reffering to the spindle bearings, or inner spindle bearings, they are best cleaned and greased and re assembled when you do the ball joint teardown.
No substitute for doing it right.
Just shooting grease in the ABS hole wont put grease in the inner spindle bearings,it wont migrate into the well for the torrington style bearing.
Pouring in gear oil will run through the bearing and wash out the grease, into the locking/unlocking hub, then it can leak out from there , making a mess.Tear it down, use good grease, do it right.
12-07-2012 06:52 PM
327NUT Thanks for your input.........but I spoke with the Ford dealer tech near me this afternoon and they said some guys do that exact thing. He also said that they sometimes shoot wheel bearing grease down the ABS bracket bolt hole then re-install the bolt. Says thats a better way to lube the bearing than the gear oil ????????? I'll have to check all this out when I have the knuckle apart.
12-07-2012 06:09 PM
familyguy Latech is right,only grease in bearings.NO gear oil.
12-07-2012 03:03 PM
LATECH Dont do it. Those are a sealed bearing also, no need for gear oil .
Manual hubs do need grease, but dont over do it. The vacuum hubs do have some grease , and if you take them apart and they are dry you can put some grease in them, on the cogs and seal lip surfaces .
On a vacuum hub system, Putting 80/140 in them will not do much except contaminate the vacuum system, probably destroy the vacuum solenoid as the gear oil will eat it , and it will swell the hoses..eventually, and then they will collapse and malfunction as well.
The 2 way manual / auto hubs are just a combination of both designs. I have seen them on F series also. Just sayin. They also use grease...not gear oil.
12-07-2012 02:10 AM
327NUT
gear oil in hub/bearing carrier?

I'm getting ready to change out the ball joints on my '02 F-250 4x4....pretty common problem with them I understand but the truck has 122K on it.

I was speaking to the owner of the truck place where I bought some of the parts from and he said he also pours 80/140 gear oil down the port on the knuckle where the vacuum line goes. I have manual locking hubs so no vac. line. He said doing this really keeps the bearings cooler and lubed 100% of the time.

I'm a complete rookie when it comes to this idea, sounds like it might work but have any of you guys done or heard of doing this. Seems like Ford would have done it from the factory if it was that good of a deal but then again they want your bearings to wear out....some time.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:44 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.