Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Compressor Regulator, line size and pipe set up
User Name
lost password?   |   register now

Thread: Compressor Regulator, line size and pipe set up Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-07-2012 08:28 PM
filter regulator.

I have a couple filter regulators. with air snap fittings that are portable. I don't run the air thru the filter reg when just using air for blowing chips when using the lathe, Mill or wood working equipment . I have a Harbor freight auto water drain plumbed with a T and manual drain todrain the compressor tank , My compressor is up in the air 8 ft high in a corner on a 4 X 4 Ft hanging from the roof, platform
12-07-2012 07:16 PM
OneMoreTime one will not lose pressure with a long line once you are hooked up you will see the same pressure everywhere in the system..the airout of the compressor is hot and needs to cool so the air/water seperator works as it only works on water that is liquid and not in the vapor form..I have a 100 feet of line between the compressor and my air/water seperator. I use one of the small dessicant inline filters after the filter regulator as a tattletale as they turn blue if any moisture is getting through..mine works fine on my plasma and for painting..

12-07-2012 06:46 PM
Ryan123 Just finished

After a little 220 and steal wool ( waiting until i get the regulators and ect. before i polish it up. its aluminium too, to help with cooling.)

whats a good quality 1/2 hose and re tractor reel?

Onemoretime, i was going to get a 3 foot hose from the compressor to the piping, is that not enough (keeping in mind i don't want to loose to much pressure with a long line)
12-07-2012 06:39 PM
Ryan123 Alright I just finished my pipe set-up, and now looking for regulator, filter and lubricator. Should i get a filter, dryer or just a filter? Any recommendations for a good quality brands. Ive been looking at a SMC ( on ebay that is 140 ( filter, regulator lubricator), Arrow and TP tools. Any input on those brands?

I like the idea about the propane tank, i just don't have the room. Im also worried about pressure drop, i was not excited about the piping that i just made but i also dont want water problems when painting.
12-07-2012 03:09 PM
air lines

There has been a lot posted here on hotrodders about plumbing in air systems, I have about 140 Ft of 1/2 Copper pipe in my shop. when I run a pipe along the wall it slops down to a drain at the end ..I put in a T with the outlet pointing up for the drop. plumbed with a upsidown U so the air goes up over then down with the snap fittings. that way any water will tend to run down the pipe to the drain. There was a tip posted a while back about using an old propane tank with new fittings added , Fill the tank with kitty litter and run the air thru it to absorb any moisture. I have the pieces, just need time to weld it up for the Plasma air supply.
12-07-2012 12:32 PM
OneMoreTime What you show n the pic will work just sure and make a good length of run in your line so the air is cool when it reaches the air/water separator so that can work..1/2 inch line is what most use..

12-07-2012 12:25 PM
Compressor Regulator, line size and pipe set up

I just bought a kobalt 80 Gallon single stage 5 HP compressor. Here are the specs:

Air Delivery SCFM @ 40PSI 17.3
Air Delivery SCFM @ 90PSI 16.1
Horsepower (HP) 5.0
Tank Capacity (Gallons) 80.0
Tank Type Stationary
Air Compressor Voltage 230

Im looking to run all air tools, from sanders, ratches, paint guns, cut offs, ect..

Ive been reading about regulators and preassure drop and im thinking that ill go with a 1/2in line, is the to big? I dont want to loose performance from restriction, but i dont want to go to big.

Now once i get the line size down, i can get a regulator. Some people hate the Harbor Freight ones, some say they are fine. I want something that will last and is rebuild-able and is not overly expensive. Im, also looking for a filter/dryer. whats the difference between a combo unit? The dryer just drips the water from the bottom correct, and a filter has a micron filter for particles right?

Next im looking at using this plumbing sechematic:

Will this be to much/needed/to little?

Thank you for looking at this, i just want to learn the differences between the units and under stand how they work.


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 06:45 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.