Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> 8 pt. roll cage
User Name
lost password?   |   register now

Thread: 8 pt. roll cage Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-06-2003 04:03 PM
Pony Yes I have a Comp Eng catalog and was going to use the Bend to order feature in the back. It will be a little while before I tackle that as I'm fitting up a set of Patriot Fake Snake Pit Side Pipes now. Thanks and I hope I helped some.
10-06-2003 02:51 PM
TurboS10 I used a Jegs prefit 10 point kit for my S-10 and modified it to use the X brace for the rear drops for added resistance to flex. I also added some 1" bracing to stiffen things up as well along with a dash bar.

Basically you get prebent tubes for th main hoop, top hoop and back brace and a bunch of tubing. I believe there were two tube ends prenotched and the rest had to be done. That I could handle, but I did not want to have to buy a bender so it worked for me.

10-06-2003 02:34 PM
383vette thanks much, I knew there were pre-fit kits avail. but I had never seen one or talked to anyone who had installed one.
10-06-2003 12:42 PM
TurboS10 Look for a prefit kit. It will save you lots of headache. They are not a perfect fit, but they are close. If you plan on racing, look up and NHRA rule book on the net so you make sure an get it in properly. Before you start completely gut the interior. Also remember welding spackle will ruin the glass and paint. Plan carfully, or you could really regret it. If you have any more questions about the process let us know.

10-05-2003 06:29 PM
8 pt. cage in a corvette

good luck & keep us posted. I am wondering if you are aware that competion engineering makes custom fitted kits for the corvettes? let us know.
10-03-2003 09:23 PM
Pony I'v got the body off my 74 stingray now as I had to replace the frame and am rebuilding as necessary while it's apart. I studied the roll bar problem quite a bit as I would like one too! Big problem = If you weld it in you can't take the body off without cutting the cage out. I suspect your car is primarily a street machine like mine, as racers cut the insides out and replace it with and aluminum interior kit. I'm thinking if I do it of: using a 4 point cage, having the rear tubes bent to point down 4" at back end of tube, weld 4 tubes aprox 3" high (that the cage tubes would fit snugly into) to my frame, cut floor pan to clear tubes, make grommets out of rubber tubing sliced open, seal it with silicone, install cage into tubes when installing body and weld up cage, then securing cage into tubes with 2 ea 1/2" grade 8 thru bolts. I'm thinking that it would handle a roll over ok and anyway Corvette owners usually get killed by fiberglass poisoning from the exploding body.
10-02-2003 03:27 PM
WICKEDFAB the one tip i have is practice practice practice....well i guess thats three tips...

do you have a bender already????if so which one?

ive been bending for 2 years and still learning on every cage i do...

you can keep all the interior if you want...building a cage is a give and take many times...sacrificing comfort over strength and reverse ya know...welding with the headliner is no biggie...just get some high dollar welding blankets.
10-02-2003 01:58 PM
8 pt. roll cage

I would like info on installing an 8 pt. cage in a 73 vette. Can the interior remain close to stock, etc. Any tips would be greatly appreciated.


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 03:42 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.