Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> T-400 problems
User Name
Password
lost password?   |   register now

Thread: T-400 problems Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-11-2012 07:24 AM
Msulli07 I popped it apart last night and found the problem. Thanks Rick for pointing me in the right direction. The Manual Valve wasnt connected to the inner linkage. Everything is running great now. I appreciate all of your guys help!
12-11-2012 04:43 AM
FmrStrtracer Double check fluid level.
Get a clean drain pan and drain the fluid.
Recheck all of your work, since it worked before you modified it, its got to be something you missed placed.
If you dont have the directions for the kit, go to B&M website and get a copy.
12-10-2012 02:40 PM
Msulli07 Converter is good.I did everything to par with the directions that came with the kit to the stage 2. The motor just free revs with no resistance. The tires do spin in reverse nuetral drive 2 and 1 if the rear is on jack stands but with no change on the rpm of the motor.
12-10-2012 02:33 PM
cobalt327
Quote:
Originally Posted by Msulli07 View Post
I have been cruising the forums and can't find any help so I finally decided to join here as you guys have secretly helped me in the past. haha. I Have a TH400 tranny that i pulled from a running driving vehicle. I replaced the pump gasket and put a B&M shift kit in it. It then sat for a few months. I put it in a buddys pickup that he tore up his 350 trans. So we put the 400 in with a new B&M converter. We filled the converter with fluid and filled the trans up. My problem is I don't have any gears at all. Just park. We put the truck on stands and the tires barely move when in gear. Not even enough to budge the truck when its back on the ground. Any ideas? I m figuring that it has something to do with the valve body. Any help would be great. Thanks guys
Loose valve body (VB) bolts, not enough fluid, disconnected or missing filter. You did bolt the converter to the flexplate?

Does the engine rev freely w/the tranny in gear, or does it feel like the engine is being held back?

You stayed w/just one kit "stage", and didn't mix stage 1 w/stage 2, for example?

You matched up the VB gaskets? You can check the old gasket to the one that you will prolly have left over to see (it's been a long time since I saw a B&M kit, so bear w/me here). If they are the same, the wrong gasket got used.
12-10-2012 02:30 PM
Msulli07 I thought I had put everything to gether as it came out but it is a possibility. Although I am not 100% sure what exactly you are talking about. If there is anyway you can further describe to me what exactly the manual valve is and where it is at in the valve body that would greatly help me.
12-10-2012 02:25 PM
rick 427 I'll take the 1st stab at it.......are you positive that the manual valve in the valve body is connected properly in the inner linkage tab?
12-10-2012 12:33 PM
Msulli07
T-400 problems

I have been cruising the forums and can't find any help so I finally decided to join here as you guys have secretly helped me in the past. haha. I Have a TH400 tranny that i pulled from a running driving vehicle. I replaced the pump gasket and put a B&M shift kit in it. It then sat for a few months. I put it in a buddys pickup that he tore up his 350 trans. So we put the 400 in with a new B&M converter. We filled the converter with fluid and filled the trans up. My problem is I don't have any gears at all. Just park. We put the truck on stands and the tires barely move when in gear. Not even enough to budge the truck when its back on the ground. Any ideas? I m figuring that it has something to do with the valve body. Any help would be great. Thanks guys

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.