Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Transmission and flywheel delima concerns
User Name
Password
lost password?   |   register now

Thread: Transmission and flywheel delima concerns Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-23-2012 08:49 PM
mh1984 Thanks to those who helped to aswer my questions. I have found a flywheel for my conversion to manual. I called advances adaptors and it turns out that all GM truck flywheels from 86 to 98 are the same.
12-18-2012 04:31 PM
mh1984 The starter is straight. It only is drilled with one bellhousing patern. It currently has a 4L60E behind it. Im rebuilding it later on to make it last with a level 4 kit. I think the new clutch disk is 11 inches ill have to measure it to be sure. Haa anybody ever done this swap before from auto to manual? All I lack is the flywheel.
12-18-2012 05:46 AM
bondo
Quote:
Originally Posted by mh1984 View Post
The engine is a 2nd gen i think. It has an internal ballance shaft and is a vortec. The rear oil seal is a one piece. Ive read that a 350 flywheel isnt a good thing to use due to the uniqe ballance of the 4.3 . My clutch kit came in today and I ordered it for a 88-90 nv3500 . The nv3500 i have is the first design and the casing is a two piece cast aluminum. The bellhusing is integeral. The nv3500 had a few design changes over the years. New venture was a partnership between chrysler and gm. The transmissions had similar designs and internal workings but one would not cross over to the other due to bellhousing bolt patterns. Im not sure if the internals cold be swaped over though.
Ayuh,.... Is the starter a straight, or staggered pattern,..??
Is the block drilled for Both patterns,..??
What diameter is the clutch,..??

A '94 is Vortec in name only, as the Vortec heads weren't Intro'd till '96...

My Guess is ya need a 14" flywheel, for a '94, 'n Up 4.3l motor...
12-17-2012 07:46 PM
mh1984 The engine is a 2nd gen i think. It has an internal ballance shaft and is a vortec. The rear oil seal is a one piece. Ive read that a 350 flywheel isnt a good thing to use due to the uniqe ballance of the 4.3 . My clutch kit came in today and I ordered it for a 88-90 nv3500 . The nv3500 i have is the first design and the casing is a two piece cast aluminum. The bellhusing is integeral. The nv3500 had a few design changes over the years. New venture was a partnership between chrysler and gm. The transmissions had similar designs and internal workings but one would not cross over to the other due to bellhousing bolt patterns. Im not sure if the internals cold be swaped over though.
12-17-2012 04:45 PM
techinspector1 Is this a Gen I or Gen II motor? I know little or nothing about the II and III motors, but will try to help. I'm told the NV3500 has an integral bellhousing that will bolt up to a SB, so I guess the only thing you'd need to know is whether it is internally balanced with a neutral flywheel or externally balanced with a weight on the flywheel. One piece seal or two piece seal would make a difference also. LT1 would have a 153 tooth ring gear I think.
12-17-2012 10:29 AM
mh1984
Transmission and flywheel delima concerns

Im in a delima. I have a 94 c1500 that has a 4l60e and im wanting to instal an nv3500 built in the year range 88-90. What year do I need to get a flywheel from in order to make this transmission work? Ive already ordered a brand new clutch kit for this transmission. I have no idea of tooth count on the flexplate nor any idea of the tooth count on rhe statee. I desperately need to get my truck rolling again. HELP PLEASE !!!!!!!!!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.